International Interchar 1190
  • International Interchar 1190

International Interchar 1190

HFA190

Thin film water-borne intumescent coating optimized for 90 and 120 minutes fire resistance, as part of the Interchar range for cellulosic fire protection, International Interchar 1190 will maintain your architectural aesthetics for fire resistance periods up to 120 minutes on structural steelwork.

Colour
Size
Finish
£446.96
VAT excluded

£536.35 Tax incl.
Quantity

Description

International Interchar 1190 is a single component, borate and chlorine free, water borne intumescent coating designed for on-site application to structural steel requiring protection from cellulosic fire. International Interchar 1190 is a low VOC acrylic intumescent material independently fire tested in accordance with BS 476 Parts 20-22.

Intended Uses:

To provide up to two hours cellulosic fire protection on beams, columns and hollow sections exposed in interior environments.

Features & Benefits:

  • Best in class loadings for 90 & 120 minutes fire resistance
  • Tested to BS 476: Parts 20 & 21
  • Loss Prevention Council Board (LPCB) Third Party Product Approval
  • LPCB Red Book Listed
  • Compatible with a wide range of primers and a full topcoat color range including water-borne options
  • Suited to on-site application
  • Fast drying characteristics for excellent productivity
  • Single pack product for fast and easy single leg airless spray application
  • High solids, low odour, zero VOC formulation*

* According to EU Solvent Emissions Directive (SED) 1999/13/EC

IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and ConditionsWe will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
HFA190

Data sheet

Application
Brush, Roller, Spray
Coverage
1m² per litre (average)
Touch Dry
2 Hours
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
16 other products in the same category:

Zeroflame Aquasteel WB+

Zeroflame Aquasteel WB+ is a White Intumescent Coating that is ideal for smaller fireproofing jobs on steel. Achieves 30 and 60 mins' fire resistance on structural steel profiles Tested to internationally accepted standards BS476 Parts 20 and 21 Certificate application included Fast drying Apply by brush, roller or airless spray...

Price £50.99 Regular price £56.66
In stock

PPG SteelGuard 702

PPG SteelGuard 702 is a one-component, thin-film solvent-borne intumescent coating for fire protection of circular and rectangular hollow-section structural steel. Provides up to 90 minutes protection from cellulosic fires and is suitable to apply on or offsite. Top Features Tested and assessed to EN 13381-8 CE marked product, ETA 15/0053...

Price £464.60
In stock

Sherwin-Williams Firetex FX5120

Sherwin-Williams Firetex FX5120 is a water based TCEP free thin film intumescent coating. Firetex FX5120 has been designed for application by airless spray, to provide fire resistance for periods of up to 120 minutes on structural steel. FX5120 can also be used to enhance the fire resistance of concrete slabs and decks up to 60 minutes. 

Price £160.06
In stock

Jotun Steelmaster 1200WF

Jotun Steelmaster 1200WF is a one component waterborne acrylic thin film intumescent coating independently tested and approved for fire protection of structural steel exposed to cellulosic fire up to 180 minutes. Suitable for properly prepared carbon steel substrates.

Price £146.11
In stock

PPG SteelGuard 751

PPG SteelGuard 751 is a one-component thin-film solvent-borne intumescent coating for fire protection of structural steelwork. Provides up to 120 minutes protection from cellulosic fires. Top Features Tested and assessed to EN 13381-8, BS 476-20/21 and AS 1530.4 CE marked product, ETA 15/0439 Assessed to ETAG 018-2 for all durability...

Price £469.20
In stock

Zeroflame Aquasteel WB+ 60min System for Steel

This pack provides sufficient intumescent basecoat (Zeroflame Aquasteel WB+) and coloured topcoat (Zeroflame Aquasteel WB+ Finish) to protect suitably primed, standard structural steel beams and columns in internal environments to 60 minute fire resistance.

Price £105.03
In stock

PPG SteelGuard 851

A one component thin-film solvent-borne intumescent coating for fire protection of structural steelwork. Short handling times are accomplished due to the fast-drying nature of this coating, and provides up to 120 minutes of protection from cellulosic fires. Top Features Suitable for C1 to C4 internal and external environments (ISO 12944);...

Price £420.20
In stock

Jotun Steelmaster 60SB

Jotun Steelmaster 60SB is a one component solvent based acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to cellulosic fire. It can be used as a mid coat or finish coat in atmospheric environments and is suitable on approved primers on carbon steel and galvanised steel substrates.

Price £195.16
In stock

Hydron Nu-Flame W Steel Basecoat

Nu-Flame W Steel Basecoat is a thin film water-based decorative intumescent paint system providing fire resistance to structural steel and cast iron. Advantages Up to 90 mins fire resistance Water-based Safe for internal use 12-month shelf life

Price £232.00
In stock

International Interchar 1290

International Interchar 1290 is a thin film waterborne intumescent coating optimised for hollow sections up to 180 minutes fire resistance whilst still maintaining aesthetics. Interchar 1290 is a single component, borate and chlorine free, water borne intumescent coating designed for on-site application to structural steel requiring protection...

Price £446.58
In stock

Thermoguard Thermocoat W

Thermoguard Thermocoat W is a White Intumescent Paint for steel, structural steel and cast iron:  Up to 90 minutes’ fire resistance Can be overcoated with compatible decorative topcoat Water-based Low odour Environmentally friendly Cost effective for large projects Certificate of supply available on request Can be applied by brush,...

Price £46.80 Regular price £52.00
In stock

Envirograf EP/FS/P Water-Based Primer for Steel

EP/FS/P Water-Based Primer for Steel is part of the Intumescent Coating for Steel & Aluminium Protection range (Product 83), helping protect steelwork with extra fire protection. For use on internal and external steelwork under Envirograf Intumescent steel paint Apply to bare, previously painted or galvanised steel Can be applied by...

Price £12.41
In stock

Sherwin-Williams FIRETEX M95/02

Sherwin-Williams FIRETEX M95/02 is an epoxy intumescent suitable for cellulosic fire protection which can be applied directly onto blast cleaned steel. It is an exterior durable intumescent, suitable for application in-shop and on site, provided the conditions specified in the product data sheet are adhered to.

Price £206.89
In stock

Nullifire S606 Solvent-Based Intumescent Coating

Nullifire S606 Solvent-Based Intumescent Coating is a single pack solvent-based intumescent coating for fire protection of both internal and external structural steelwork. S606 is very pale pink in colour. S606 provides effective structural fire protection for steelwork, from 60 minutes up to a 120 minute fire rating. Suitable for universal and hollow...

Price £177.12
In stock

Nullifire S708 Durable Water-Based Intumescent Basecoat

Nullifire S708 Durable Water-Based Intumescent Basecoat is a white thin film intumescent coating for the fire protection of internal and semi-exposed structural steelwork but can be fully exposed during construction. It can provide up to 60 minutes fire resistance.

Price £163.76
In stock