Call 0113 245 5450 for Sales or Technical
Alternatively you can email our sales & support team on [email protected]
Sherwin-Williams FIRETEX FX9500, a 2 -pack exterior durable intumescent offering 60, 90 & 120 minute fire protection both internally and externally without topcoat, which can be applied directly onto blast cleaned steel. Suitable for application in-shop and on site.
Sherwin-Williams FIRETEX FX9500 is an exterior durable intumescent, which can be applied directly onto blast cleaned steel and is suitable for application in-shop and on site, provided the conditions listed in the product data sheet are adhered to. For use in internal and external environments without topcoat.
Sherwin-Williams FIRETEX FX9500 utilises hydrocarbon fire technology and a long standing track record which includes some of the world's most iconic structures marking the next generation in epoxy intumescent coatings, on projects where external long term durability is a concern.
Offering an aesthetically pleasing appearance which requires no back rolling or sanding, Sherwin-Williams FIRETEX FX9500 is a cost effective, scrim free, high volume solids product, with user friendly application properties which can be applied by single airless leg spray.
*As defined in ISO 12944-2:1998 with appropriate maintenance.
**Based on 60 minute protection, 25-30% would be achieved on 120 minute protection
Where a high degree of gloss and colour retention is required overcoat with Acrolon C137V2, Acrolon 7300, Acrolon 1850 within 7 days at a minimum dft of 50 microns or in the case of Acrolon C750V2 overcoat within 4 days. These overcoating times refer to achievement of optimum adhesion at 23°C and will vary with temperature.
Sherwin-Williams FIRETEX FX9500 is indefinitely over-coatable with itself.
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Sherwin-Williams Acrolon 1850 is a two pack Isocyanate free finish based on an acrylic epoxy binder system. It is a finish coat for exterior exposed surfaces where retention of gloss is required, and the use of isocyanate products is precluded or undesirable.
Sherwin-Williams Macropoxy C400W (formerly known as Epigrip C400W) is a multi-functional epoxy zinc phosphate coating specified for use as a primer on blast cleaned structural steel for internal and external environments. Sherwin-Williams Macropoxy C400W may also be used as a high build intermediate coat as well as the final coat where a low...
Sherwin-Williams Acrolon C750V2 (formerly known as Leighs C750V2) is an isocyanate free, two-pack finish coat for exterior exposed surfaces where retention of gloss is required, and the use of isocyanate products is precluded or undesirable. Sherwin-Williams Acrolon C750V2 is normally used in conjunction with epoxy primers and undercoats and is Highways...
Sherwin-Williams Acrolon 7300 is a high solids, tin free polyurethane, with fast drying and high gloss attributes. Acrolon 7300 can suitable for use where long term exterior gloss and colour retention characteristics are required.
Sherwin-Williams Firetex FX2005, a single pack thin film intumescent coating designed for in-shop application by airless spray to provide fire resistance for up to 120 minutes on structural steel. Tested and assessed to EN13381-8 European Technical Approval 16-0588 CE Marking Number 1121-CPR-GA5030 Can resist normal weather conditions...
Sherwin-Williams FIRETEX M95/02 is an epoxy intumescent suitable for cellulosic fire protection which can be applied directly onto blast cleaned steel. It is an exterior durable intumescent, suitable for application in-shop and on site, provided the conditions specified in the product data sheet are adhered to.
EP/FS/TCE Spirit-Based Top Coating for Steel is part of the Intumescent Coating for Steel & Aluminium Protection range (Product 83), helping protect steelwork with extra fire protection. 5L size can be tinted to over 350+ colours in RAL & BS shades Opaque topcoat Forms a flexible film over intumescent coatings For external areas...
Jotun Steelmaster 600WF is specially designed as passive fire protection for steel constructions. Designed to protect up to 60 minutes on a wide range of I section beams and columns. Will provide 90 minutes fire duration as per BS476 part 20-21. Suitable for structural steel exposed to internal environments up to corrosivity category C3 (ISO...
A one component thin-film solvent-borne intumescent coating for fire protection of structural steelwork, providing up to 120 minutes of protection from cellulosic fires. Top Features Suitable for C1 to C4 internal and external environments (ISO 12944); for dry internal (C1) environments no topcoat is required Tested and assessed to EN...
International Interchar 1120 is a single component, borate and chlorine free, water borne intumescent coating designed for on-site application to interior exposed structural steel requiring protection from cellulosic fire. A low VOC intumescent material independently fire tested that will maintain your architectural aesthetics for fire...
Zeroflame Aquasteel WB+ is a White Intumescent Coating that is ideal for smaller fireproofing jobs on steel. Achieves 30 and 60 mins' fire resistance on structural steel profiles Tested to internationally accepted standards BS476 Parts 20 and 21 Certificate application included Fast drying Apply by brush, roller or airless spray...
A one-component, thin-film solvent-borne intumescent coating for fire protection of circular and rectangular hollow section structural steel. Top Features Tested and assessed to EN 13381-8 CE marked product, ETA 15/0053 Assessed to ETAG 018-2 for all durability classifications
EP/FS/IN/WB Water Based Intumescent Coating for Steel Protection is part of the Intumescent Coating for Steel & Aluminium Protection range (Product 83), helping protect steelwork with extra fire protection. Smooth finish Internal & external use Can be applied over existing painted steel Apply with a brush, roller or spray
Jotun Steelmaster 120SB is a one component solvent based acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to celulosic fire. It can be used as mid coat or finish coat in atmospheric environments and is suitable on approved primers on carbon steel and galvanised steel substrates.
EP/FS/P Water-Based Primer for Steel is part of the Intumescent Coating for Steel & Aluminium Protection range (Product 83), helping protect steelwork with extra fire protection. For use on internal and external steelwork under Envirograf Intumescent steel paint Apply to bare, previously painted or galvanised steel Can be applied by...
Intershield Flexible Top Coat is part of the Intumescent Coating for Steel & Aluminium Protection range, helping protect steelwork with extra fire protection. Chlorinated rubber flame retardent Complies with BS476 Parts 6 & 7, Class 0 & Class 1 (1987) Spread of flame Apply by brush, roller or sprayer No thinning required
EP/FS/TCW Water-Based Top Coating for Steel is part of the Intumescent Coating for Steel & Aluminium Protection range, helping protect steelwork with extra fire protection. Hard & glossy top coat Good weather resistance Apply with a brush, roller or spray For internal & non-exposed areas
International Interchar 212 is a high performance, high build, solvent free, two pack modified epoxy intumescent fireproofing coating designed to be used on steelwork requiring protection from cellulosic fires.
International Interchar 2090 is a single component, solvent borne, borate free, high solids, low VOC intumescent coating designed to maintain your architectural aesthetics whilst providing fire protection for up to 120 minutes for columns, I-sections, cellular beams and hollows.
PPG SteelGuard 564 is a one-component, thin-film, solvent-borne intumescent coating for fire protection of structural steelwork. Steelguard 564 is fast-drying and can provide up to 120 minutes protection. Top Features Suitable for C1 to C4 internal and external environments (ISO 12944); for dry internal (C1) environments no topcoat is...
