Sherwin-Williams Firetex FX5062
  • Sherwin-Williams Firetex FX5062

Sherwin-Williams Firetex FX5062

FX5062

Sherwin-Williams Firetex FX5062 is a water-based TCEP free thin film intumescent coating, specifically designed for airless spray application to provide fire resistance for periods up to 90 mins on structural steel. Firetex FX5062 has been Certifire Approved.

Colour
Size
Finish
£216.51
VAT excluded

£259.81 Tax incl.
Quantity

Description

Endorsements

  • Certifire Approved – Certificate CF5267
  • This product has been tested and assessed in accordance with the ASFP “Yellow Book” 5th Edition.

Recommended Primers

  • A range of primers have been fire tested and approved for use under FIRETEX FX5062.
  • Please consult Rawlins Paints for detailed information.
  • Must not be applied directly to galvanized steel and zinc rich primers. 

Recommended Topcoats

If it can be guaranteed that application and subsequent in-service conditions will be in a C1 environment as defined in ISO 12944-2:2007, then no topcoat is required.

For any other situation a topcoat must be applied, consult our Technical Team for advice.

The above products should be used for subsequent re-decoration.

Additional Notes

In common with other water based coatings, the drying of this material is retarded by high humidity conditions. Lack of air movement also slows down the drying process, and under such conditions it is advisable to introduce some method of circulating air over the coated surface in order to speed up the drying. A ventilated air speed of 2 metres per second is recommended.

Numerical values quoted for physical data may vary slightly from batch to batch. 

IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and ConditionsWe will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
FX5062

Data sheet

Touch Dry
1.5 hours
Application
Brush, Spray
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions stuart miles on 24/04/2017
Question: can this paint be sprayed on and does it have to be applied in a controlled manner no one else working in that area?
Answer: 

Sherwin-Williams Firetex FX5062 is a water-based TCEP free thin film intumescent coating, specifically designed for airless spray application. For further details on spray application and set up refer to the product TDS (Technical Data Sheet) available to download from the 'DATASHEETS' tab on the product page.


Question about the product

* Required fields
(read)
Send
16 other products in the same category:

Sherwin-Williams Firetex FX5090

Sherwin-Williams Firetex FX5090 is a water based TCEP free thin film intumescent coating, designed for application by airless spray to provide fire resistance for periods of up to 120 minutes on structural steel.   

Price £253.64
In stock

Zeroflame Aquasteel WB+ 60min System for Steel

This pack provides sufficient intumescent basecoat (Zeroflame Aquasteel WB+) and coloured topcoat (Zeroflame Aquasteel WB+ Finish) to protect suitably primed, standard structural steel beams and columns in internal environments to 60 minute fire resistance.

Price £105.03
In stock

International Interchar 2060

International Interchar 2060 is a single component, solvent borne, borate free, high solids, low VOC, thin film intumescent coating optimized for 60 minutes fire resistance to structural steelwork. Independently tested at accredited laboratories to BS476 Parts 20-21, AS 1530.4-2005 and AS 4100, and third party assessed and certified.

Price £297.00
In stock

International Interchar 1120

International Interchar 1120 is a single component, borate and chlorine free, water borne intumescent coating designed for on-site application to interior exposed structural steel requiring protection from cellulosic fire. A low VOC intumescent material independently fire tested that will maintain your architectural aesthetics for fire resistance periods...

Price £446.58
In stock

Sherwin-Williams Firetex M95

Sherwin-Williams Firetex M95 is an epoxy intumescent suitable for cellulosic fire protection. Firetex M95 is an exterior durable intumescent, which can be applied directly onto blast cleaned steel. 

Price £242.27
In stock

Jotun Steelmaster 60/120

Jotun Steelmaster 60/120 is a one component solvent based acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to celulosic fire. It can be used as a mid coat or finish coat in atmospheric environments and is suitable on approved primers on carbon steel and galvanised steel substrates.

Price £63.29
In stock

Sherwin-Williams Firetex FX5060

Sherwin-Williams Firetex FX5060 is a water-based TCEP free thin film intumescent coating. It has been designed for application by airless spray to provide fire resistance up to 60 minutes on structural steel.

Price £177.31
In stock

Hydron Nu-Flame Steel Gloss Topcoat

Nu-Flame Steel Top Coat is a flame retardant coating for internal and external steel and cast iron. Resistant to physical damage, it is also great for use in spaces that are used frequently. Advantages For steel and cast iron. Flame retardant. Anti-corrosion coating. Extend lifespan for up to 50 years. Gloss and semi gloss finishes.

Price £63.00
In stock

Jotun Steelmaster 1200WF

Jotun Steelmaster 1200WF is a one component waterborne acrylic thin film intumescent coating independently tested and approved for fire protection of structural steel exposed to cellulosic fire up to 180 minutes. Suitable for properly prepared carbon steel substrates.

Price £146.11
In stock

Sherwin-Williams Firetex FX2003

Sherwin-Williams Firetex FX2003 is single pack thin film intumescent coating, designed for in-shop application by airless spray to provide fire resistance for up to 120 minutes on structural steel. 

Price £278.29
In stock

Jotun Steelmaster 60SB

Jotun Steelmaster 60SB is a one component solvent based acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to cellulosic fire. It can be used as a mid coat or finish coat in atmospheric environments and is suitable on approved primers on carbon steel and galvanised steel substrates.

Price £195.16
In stock

Nullifire S606 Solvent-Based Intumescent Coating

Nullifire S606 Solvent-Based Intumescent Coating is a single pack solvent-based intumescent coating for fire protection of both internal and external structural steelwork. S606 is very pale pink in colour. S606 provides effective structural fire protection for steelwork, from 60 minutes up to a 120 minute fire rating. Suitable for universal and hollow...

Price £177.12
In stock

Zeroflame Aquasteel WB+ 30min System for Steel

This pack provides sufficient intumescent basecoat (Zeroflame Aquasteel WB+) and coloured topcoat (Zeroflame Aquasteel WB+ Finish) to protect suitably primed, standard structural steel beams and columns in internal environments to 30 minute fire resistance.

Price £105.03
In stock

Sherwin-Williams Firetex FX1003

Sherwin-Williams Firetex FX1003 is a single pack, thin film intumescent coating, designed for site application by airless spray, to provide fire resistance for up to 120 minutes on structural steel.

Price £278.29
In stock