Sherwin-Williams Firetex M95
  • Sherwin-Williams Firetex M95

Sherwin-Williams Firetex M95

M95

Sherwin-Williams Firetex M95 is an epoxy intumescent suitable for cellulosic fire protection. Firetex M95 is an exterior durable intumescent, which can be applied directly onto blast cleaned steel. 

Colour
Size
Finish
£242.27
VAT excluded

£290.72 Tax incl.
Quantity

Description

Sherwin-Williams Firetex M95 is an epoxy intumescent suitable for cellulosic fire protection. Firetex M95 is an exterior durable intumescent, which can be applied directly onto blast cleaned steel. 

Suitable for application in-shop and on site, provided the conditions listed in the datasheet are adhered to.

After application, unless a sealer coat is applied prior to exposure, the coating must be protected from the weather until the material reaches a shore D hardness of 50 in order to become exterior durable. Applications below 15°C may result in insufficient curing and reduced weather resistance and performance. See application conditions and over-coating. 

Endorsements

Certifire Approved – Certificate CF500

Recommended Primers

  • Macropoxy L574 Blast Primer
  • Macropoxy C425V2 Zinc Phosphate Primer 
  • Macropoxy C400 Range
  • Macropoxy M111 Wet Blast Primer 
  • Firetex C69 Fast-Track Blast Primer 

Recommended Topcoats

Indefinitely overcoatable with high performance systems provided the surfaces to be coated are free from all contaminants. Where a high degree of gloss and colour retention is required overcoat with Acrolon C137V2 within 7 days at a minimum dft of 50 microns or in the case of Acrolon C750V2 overcoat within 4 days. These overcoating times refer to achievement of optimum adhesion at 23°C and will vary with temperature.

Firetex M95 is indefinitely overcoatable with itself. 

IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and ConditionsWe will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
M95

Data sheet

Touch Dry
5 Hours
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
16 other products in the same category:

Nullifire S708 Durable Water-Based Intumescent Basecoat

Nullifire S708 Durable Water-Based Intumescent Basecoat is a white thin film intumescent coating for the fire protection of internal and semi-exposed structural steelwork but can be fully exposed during construction. It can provide up to 60 minutes fire resistance.

Price £163.76
In stock

Sherwin-Williams Firetex FX5090

Sherwin-Williams Firetex FX5090 is a water based TCEP free thin film intumescent coating, designed for application by airless spray to provide fire resistance for periods of up to 120 minutes on structural steel.   

Price £253.64
In stock

PPG Steelguard 751

A one-component thin-film solvent-borne intumescent coating for fire protection of structural steelwork. Provides up to 120 minutes protection from cellulosic fires. Top Features Tested and assessed to EN 13381-8, BS 476-20/21 and AS 1530.4 CE marked product, ETA 15/0439 Assessed to ETAG 018-2 for all durability classifications

Price £469.20
In stock

International Interchar 1260

International Interchar 1260 is a single component, borate, chlorine and APEO free, water borne intumescent coating designed for on-site application to interior exposed structural steel requiring protection from cellulosic fire. 

Price £446.96
In stock

PPG Steelguard 801

A one component thin-film solvent-borne intumescent coating for fire protection of structural steelwork, providing up to 120 minutes of protection from cellulosic fires. Top Features Suitable for C1 to C4 internal and external environments (ISO 12944); for dry internal (C1) environments no topcoat is required Tested and assessed to EN...

Price £400.00
In stock

Nullifire TS815 Solvent-Based Acrylic Top Seal

Nullifire TS815 Solvent-Based Acrylic Top Seal is a single pack, high build modified acrylic topseal conforming to 2010 VOC limits. This product is designed for use with the Nullifire System S range of intumescent basecoats. 

Price £70.55
In stock

International Interchar 1190

Thin film water-borne intumescent coating optimized for 90 and 120 minutes fire resistance, as part of the Interchar range for cellulosic fire protection, International Interchar 1190 will maintain your architectural aesthetics for fire resistance periods up to 120 minutes on structural steelwork.

Price £446.96
In stock

Jotun Steelmaster 60WB

Jotun Steelmaster 60WB is a one component waterborne acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to cellulosic fire. ADVANTAGES Best loadings for beams and columns Low VOC, water-borne Single coat application for a majority of 60minute steel sections Low odour Tested to...

Price £120.46
In stock

Zeroflame Aquasteel WB+ 60min System for Steel

This pack provides sufficient intumescent basecoat (Zeroflame Aquasteel WB+) and coloured topcoat (Zeroflame Aquasteel WB+ Finish) to protect suitably primed, standard structural steel beams and columns in internal environments to 60 minute fire resistance.

Price £105.03
In stock

Jotun Steelmaster 120SB

Jotun Steelmaster 120SB is a one component solvent based acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to celulosic fire. It can be used as mid coat or finish coat in atmospheric environments and is suitable on approved primers on carbon steel and galvanised steel substrates.

Price £195.23
In stock

Sherwin-Williams Firetex FX5120

Sherwin-Williams Firetex FX5120 is a water based TCEP free thin film intumescent coating. Firetex FX5120 has been designed for application by airless spray, to provide fire resistance for periods of up to 120 minutes on structural steel. FX5120 can also be used to enhance the fire resistance of concrete slabs and decks up to 60 minutes. 

Price £120.29
In stock