Sherwin-Williams Firetex J220 Scrim Cloth is a high temperature jet fire resistant fabric scrim cloth designed to reinforce the insulation ‘char’ developed when Firetex M90/02 reacts in a fire.
Sherwin-Williams Sher-Cryl M770
Sherwin-Williams Sher-Cryl M770 (formerly known as Envirogard M770) is a water based quick drying gloss finish or sealercoat for the entire Sherwin-Williams FX product range.
Sherwin-Williams Sher-Cryl M770 is used in areas where solvent emissions are not desirable. It may also be used as an essential decorative sealer-coat for the FX product range to provide resistance to moisture.
BS476 Part 7 Surface Spread of Flame Material - for details of substrate/scheme, consult our Technical Team.
Indefinitely self-overcoatable. For details of overcoating with other materials, consult Rawlins Paints.
In common with other water based materials, drying of this material is retarded by high humidity conditions. Lack of air movement also slows down the process, and under such conditions it is advisable to introduce some method of circulating air over the coated surface to speed up the drying.
An air speed of 2 metres per second is recommended. When used as a sealer-coat over the FX product range, a slight reduction in final gloss level will be observed. This does not detract from exposure performance, nor fire resistance properties.
Certain shades, for example reds and yellows, may require additional coats to achieve full opacity.
Numerical values quoted for physical data may vary slightly from batch to batch.
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Typical Coverage (per coat)
- 11.1m² per litre
- Touch Dry
- 15 Minutes
- Brush, Roller, Spray
Be the first to ask a question about this product!
International Interchar 1290 is a thin film waterborne intumescent coating optimised for hollow sections up to 180 minutes fire resistance whilst still maintaining aesthetics. Interchar 1290 is a single component, borate and chlorine free, water borne intumescent coating designed for on-site application to structural steel requiring protection...
Nu-Flame W Steel Basecoat is a thin film water-based decorative intumescent paint system providing fire resistance to structural steel and cast iron. Advantages Up to 90 mins fire resistance Water-based Safe for internal use 12-month shelf life
International Interchar 1120 is a single component, borate and chlorine free, water borne intumescent coating designed for on-site application to interior exposed structural steel requiring protection from cellulosic fire. A low VOC intumescent material independently fire tested that will maintain your architectural aesthetics for fire resistance periods...
International Interchar 2090 is a single component, solvent borne, borate free, high solids, low VOC intumescent coating designed to maintain your architectural aesthetics whilst providing fire protection for up to 120 minutes for columns, I-sections, cellular beams and hollows.
International Interchar 2060 is a single component, solvent borne, borate free, high solids, low VOC, thin film intumescent coating optimized for 60 minutes fire resistance to structural steelwork. Independently tested at accredited laboratories to BS476 Parts 20-21, AS 1530.4-2005 and AS 4100, and third party assessed and certified.
Jotun Steelmaster 60SB is a one component solvent based acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to cellulosic fire. It can be used as a mid coat or finish coat in atmospheric environments and is suitable on approved primers on carbon steel and galvanised steel substrates.
Bollom Brosteel Ultra 60 is a White Intumescent Paint for structural steel members: Provides 30 and 60 minutes’ fire resistance For internal use only Water-based Quick drying Certificate of Conformance and Installation available on request Can be applied by brush, roller or airless spray Fully fire tested BS476:Part 20/21:1987...
Nullifire TS816 Water-Based Acrylic Top Seal is a waterborne, acrylic eggshell decorative topseal. It is primarily for use with Nullifire Intumescent Basecoats on internal steelwork.
International Interchar 212 is a high performance, high build, solvent free, two pack modified epoxy intumescent fireproofing coating designed to be used on steelwork requiring protection from cellulosic fires.
Jotun Steelmaster 120SB is a one component solvent based acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to celulosic fire. It can be used as mid coat or finish coat in atmospheric environments and is suitable on approved primers on carbon steel and galvanised steel substrates.
This pack provides sufficient intumescent basecoat (Zeroflame Aquasteel WB+) and coloured topcoat (Zeroflame Aquasteel WB+ Finish) to protect suitably primed, standard structural steel beams and columns in internal environments to 60 minute fire resistance.
Thermoguard Thermocoat W is a White Intumescent Paint for steel, structural steel and cast iron: Up to 90 minutes’ fire resistance Can be overcoated with compatible decorative topcoat Water-based Low odour Environmentally friendly Cost effective for large projects Certificate of supply available on request Can be applied by brush,...