Nullifire FC101 Intumescent Coating Repair Filler
  • Nullifire FC101 Intumescent Coating Repair Filler

Nullifire FC101 Intumescent Coating Repair Filler

350487

Nullifire FC101 Intumescent Coating Repair Filler is a single pack, high build filler based on thermoplastic acrylic resin and hydrocarbon solvent designed specifically for the repair of minor damage to System S Intumescent Basecoats applied to structural steelwork. 

Colour
Size
Finish
£22.50
VAT excluded

£27.00 Tax incl.
Quantity

Description

Nullifire FC101 Intumescent Coating Repair Filler can be used internally with Nullifire S602/3/5/6, S607 and S609 Basecoats or externally with Nullifire S605 Basecoat. 

Application Check List

When applying Nullifire FC101 Intumescent Coating Repair Filler, ensure that:

  • Surface preparation has been carried out correctly.
  • The product has been stored under correct conditions.
  • Correct equipment is available.
  • The site conditions are within specification.
  • You are fully conversant with the application instructions and MSDS.

Surface Preparation

It is recommended that the filler is applied onto areas, which are a maximum of 150mm².

The surface preparation required prior to application of System S Filler is dependent upon the nature of the damage to be repaired.

For minor scratches to basecoat, which has not been topsealed and where there is no damage to primer, then the only preparation required is to abrade any material, which is proud of the basecoat surface and to ensure that the surface is clean prior to Filler application.

Where the damage is more severe, resulting in damage to the primer system exposing bare steel (particularly in external and humid internal conditions), then the primer should be touched up with a suitable anticorrosion primer and allowed to dry, prior to application of System S Filler. It may be necessary to remove a further area of basecoat surrounding the exposed steel to facilitate primer touch-up depending on the scale of damage.

Where damage occurs to basecoat, which has been topsealed, but where the damage does not penetrate through the primer to the steel surface, then the topseal should be abraded back to basecoat for a distance of 50-75mm around the affected area. This is to eliminate the possibility of the Filler overlapping onto topseal. 

IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and ConditionsWe will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
350487
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
16 other products in the same category:

Sherwin-Williams Firetex FX5120

Sherwin-Williams Firetex FX5120 is a water based TCEP free thin film intumescent coating. Firetex FX5120 has been designed for application by airless spray, to provide fire resistance for periods of up to 120 minutes on structural steel. FX5120 can also be used to enhance the fire resistance of concrete slabs and decks up to 60 minutes. 

Price £120.29
In stock

International Interchar 1260

International Interchar 1260 is a single component, borate, chlorine and APEO free, water borne intumescent coating designed for on-site application to interior exposed structural steel requiring protection from cellulosic fire. 

Price £446.96
In stock

Sherwin-Williams Firetex M95

Sherwin-Williams Firetex M95 is an epoxy intumescent suitable for cellulosic fire protection. Firetex M95 is an exterior durable intumescent, which can be applied directly onto blast cleaned steel. 

Price £242.27
In stock

Jotun Steelmaster 60/120

Jotun Steelmaster 60/120 is a one component solvent based acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to celulosic fire. It can be used as a mid coat or finish coat in atmospheric environments and is suitable on approved primers on carbon steel and galvanised steel substrates.

Price £63.29
In stock

Sherwin-Williams FIRETEX M95/02

Sherwin-Williams FIRETEX M95/02 is an epoxy intumescent suitable for cellulosic fire protection which can be applied directly onto blast cleaned steel. It is an exterior durable intumescent, suitable for application in-shop and on site, provided the conditions specified in the product data sheet are adhered to.

Price £258.43
In stock

Sherwin-Williams Firetex M72

Sherwin-Williams Firetex M72 is a solvent based intumescent mastic coating, used for the repair of small areas of mechanical damage to Firetex range of intumescent coatings.

Price £37.29
In stock

Jotun Steelmaster 60WB

Jotun Steelmaster 60WB is a one component waterborne acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to cellulosic fire. ADVANTAGES Best loadings for beams and columns Low VOC, water-borne Single coat application for a majority of 60minute steel sections Low odour Tested to...

Price £120.46
In stock

Sherwin-Williams Firetex M71V2

Sherwin-Williams Firetex M71V2 is a sheen decorative topcoat for the Firetex range of single pack intumescent coatings and also provides protection when used in internal semi-controlled conditions where condensation may occur (Category C2 as defined in ISO 12944-2).

Price £70.69
In stock

International Interchar 1120

International Interchar 1120 is a single component, borate and chlorine free, water borne intumescent coating designed for on-site application to interior exposed structural steel requiring protection from cellulosic fire. A low VOC intumescent material independently fire tested that will maintain your architectural aesthetics for fire resistance periods...

Price £446.58
In stock

International Interchar 2060

International Interchar 2060 is a single component, solvent borne, borate free, high solids, low VOC, thin film intumescent coating optimized for 60 minutes fire resistance to structural steelwork. Independently tested at accredited laboratories to BS476 Parts 20-21, AS 1530.4-2005 and AS 4100, and third party assessed and certified.

Price £297.00
In stock

Sherwin-Williams Firetex FX1003

Sherwin-Williams Firetex FX1003 is a single pack, thin film intumescent coating, designed for site application by airless spray, to provide fire resistance for up to 120 minutes on structural steel.

Price £278.29
In stock

Sherwin-Williams Firetex FX5090

Sherwin-Williams Firetex FX5090 is a water based TCEP free thin film intumescent coating, designed for application by airless spray to provide fire resistance for periods of up to 120 minutes on structural steel.   

Price £253.64
In stock

Hydron Nu-Flame Steel Gloss Topcoat

Nu-Flame Steel Top Coat is a flame retardant coating for internal and external steel and cast iron. Resistant to physical damage, it is also great for use in spaces that are used frequently. Advantages For steel and cast iron. Flame retardant. Anti-corrosion coating. Extend lifespan for up to 50 years. Gloss and semi gloss finishes.

Price £63.00
In stock