Envirograf Mordant Solution
  • Envirograf Mordant Solution

Envirograf Mordant Solution

Product 83

Mordant Solution is part of the Intumescent Coating for Steel & Aluminium Protection range, helping protect steelwork with extra fire protection.

  • Prepares galvanised steel prior to coating
  • Treats approx. 15 square metres per litre
  • Available in 1L to 5L quantities
Size
£26.94
VAT excluded

£32.33 Tax incl.
Quantity

Description

Envirograf Mordant Solution, part of the Intumescent Coating for Steel & Aluminium Protection range. Prepares and pre-treats galvanised steel before applying protection coatings.

Application:

Ensure any oil and grease is removed from the surface to be treated. Allow the surface to dry before application of subsequent coating.

Thoroughly work Mordant Solution into the surface using a brush ensuring all the surface changes colour (blackens). If no initial reaction takes place, then a second application may be required. Rinse with clean water and allow to dry.

  • Coverage: Mordant Solution will treat approximately 15 square metres per litre
  • Drying Time: 30 minutes minimum – 24 hours maximum.
  • Thinner: not applicable
  • VOC Content: not applicable
  • Film Thickness: not applicable

Precautions

  • Irritating to eyes
  • Contains: Propan-2-ol
  • Use only in well ventilated areas
  • Vapours may cause drowsiness and dizziness
  • Avoid contact with skin and eyes
  • In case of contact with eyes, rinse immediately with plenty of water and seek medical advice
  • After contact with skin, wash immediately with plenty of water
  • Wear suitable protective clothing, gloves and eye/face protection
  • If swallowed, seek medical advice immediately and show the container or label
  • Keep out of the reach of children.

IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and ConditionsWe will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
Product 83
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
16 other products in the same category:

Nullifire FC101 Intumescent Coating Repair Filler

Nullifire FC101 Intumescent Coating Repair Filler is a single pack, high build filler based on thermoplastic acrylic resin and hydrocarbon solvent designed specifically for the repair of minor damage to System S Intumescent Basecoats applied to structural steelwork. 

Price £22.50
In stock

Sherwin-Williams Firetex FX5090

Sherwin-Williams Firetex FX5090 is a water based TCEP free thin film intumescent coating, designed for application by airless spray to provide fire resistance for periods of up to 120 minutes on structural steel.   

Price £163.65
In stock

Nullifire S708 Durable Water-Based Intumescent Basecoat

Nullifire S708 Durable Water-Based Intumescent Basecoat is a white thin film intumescent coating for the fire protection of internal and semi-exposed structural steelwork but can be fully exposed during construction. It can provide up to 60 minutes fire resistance.

Price £163.76
In stock

Bollom Brosteel Ultra 60

Due to product development the manufacturer of this product have temporarily removed it from sale - We expect to see it return in August 2019. In the meantime we can recommend Zeroflame Aquasteel WB+ as a great alternative. Bollom Brosteel Ultra 60 is a White Intumescent Paint for structural steel members:  Provides 30 and 60 minutes’ fire...

In stock

International Interchar 1260

International Interchar 1260 is a single component, borate, chlorine and APEO free, water borne intumescent coating designed for on-site application to interior exposed structural steel requiring protection from cellulosic fire. 

Price £446.96
In stock

Jotun Steelmaster 1200WF

Jotun Steelmaster 1200WF is a one component waterborne acrylic thin film intumescent coating independently tested and approved for fire protection of structural steel exposed to cellulosic fire up to 180 minutes. Suitable for properly prepared carbon steel substrates.

Price £146.11
In stock

PPG SteelGuard 801

A one component thin-film solvent-borne intumescent coating for fire protection of structural steelwork, providing up to 120 minutes of protection from cellulosic fires. Top Features Suitable for C1 to C4 internal and external environments (ISO 12944); for dry internal (C1) environments no topcoat is required Tested and assessed to EN...

Price £400.00
In stock

PPG SteelGuard 751

PPG SteelGuard 751 is a one-component thin-film solvent-borne intumescent coating for fire protection of structural steelwork. Provides up to 120 minutes protection from cellulosic fires. Top Features Tested and assessed to EN 13381-8, BS 476-20/21 and AS 1530.4 CE marked product, ETA 15/0439 Assessed to ETAG 018-2 for all durability...

Price £469.20
In stock

Jotun Steelmaster 600WF

Jotun Steelmaster 600WF is specially designed as passive fire protection for steel constructions. Designed to protect up to 60 minutes on a wide range of I section beams and columns. Will provide 90 minutes fire duration as per BS476 part 20-21. Suitable for structural steel exposed to internal environments up to corrosivity category C3 (ISO...

Price £56.19
In stock

Sherwin-Williams Firetex M72

Sherwin-Williams Firetex M72 is a solvent based intumescent mastic coating, used for the repair of small areas of mechanical damage to Firetex range of intumescent coatings.

Price £42.61
In stock

Sherwin-Williams Firetex J220 Scrim Cloth

Sherwin-Williams Firetex J220 Scrim Cloth is a high temperature jet fire resistant fabric scrim cloth designed to reinforce the insulation ‘char’ developed when Firetex M90/02 reacts in a fire. 

Price £1,503.62
In stock

Sherwin-Williams Firetex FX5060

Sherwin-Williams Firetex FX5060 is a water-based TCEP free thin film intumescent coating. It has been designed for application by airless spray to provide fire resistance up to 60 minutes on structural steel.

Price £150.98
In stock

PPG SteelGuard 702

PPG SteelGuard 702 is a one-component, thin-film solvent-borne intumescent coating for fire protection of circular and rectangular hollow-section structural steel. Provides up to 90 minutes protection from cellulosic fires and is suitable to apply on or offsite. Top Features Tested and assessed to EN 13381-8 CE marked product, ETA 15/0053...

Price £464.60
In stock

Sherwin-Williams Firetex FX5120

Sherwin-Williams Firetex FX5120 is a water based TCEP free thin film intumescent coating. Firetex FX5120 has been designed for application by airless spray, to provide fire resistance for periods of up to 120 minutes on structural steel. FX5120 can also be used to enhance the fire resistance of concrete slabs and decks up to 60 minutes. 

Price £160.06
In stock

Sherwin-Williams Firetex M95

Sherwin-Williams Firetex M95 is an epoxy intumescent suitable for cellulosic fire protection. Firetex M95 is an exterior durable intumescent, which can be applied directly onto blast cleaned steel. 

Price £172.41
In stock