Sherwin-Williams Sher-Cryl M770 (formerly known as Envirogard M770) is a water based quick drying gloss finish or sealercoat for the entire Sherwin-Williams FX product range.
Thermoguard High Build Metal Primer
Thermoguard High Build Metal Primer is the compatible, corrosion-resistant primer recommended for use on suitably prepared steel prior to the application of Thermoguard Thermocoat W.
- High build
- Quick dry
- Corrosion resistant
- Protects during construction
Thermoguard High Build Metal Primer is a solvent based, quick drying, corrosion resistant metal primer for structural steel in shop or on site. Compatible with Thermoguard Thermocoat W and most other intumescent paint systems, epoxy and conventional paints.
- Ideally with Thermoguard Thermocoat W
- Steel fabricator’s shops
- Work sites
Thermoguard High Build Metal Primer will protect exposed structural steel during construction as well as protecting internal steelwork thereafter.
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Typical Coverage (per coat)
- 6m² per litre
- Touch Dry
- 30 mins
- Brush, Roller, Spray
Be the first to ask a question about this product!
Sherwin-Williams Firetex FX5062 is a water-based TCEP free thin film intumescent coating, specifically designed for airless spray application to provide fire resistance for periods up to 90 mins on structural steel. Firetex FX5062 has been Certifire Approved.
Sherwin-Williams Firetex FX5060 is a water-based TCEP free thin film intumescent coating. It has been designed for application by airless spray to provide fire resistance up to 60 minutes on structural steel.
A one component thin-film solvent-borne intumescent coating for fire protection of structural steelwork, providing up to 120 minutes of protection from cellulosic fires. Top Features Suitable for C1 to C4 internal and external environments (ISO 12944); for dry internal (C1) environments no topcoat is required Tested and assessed to EN...
Nullifire FC101 Intumescent Coating Repair Filler is a single pack, high build filler based on thermoplastic acrylic resin and hydrocarbon solvent designed specifically for the repair of minor damage to System S Intumescent Basecoats applied to structural steelwork.
Sherwin-Williams Firetex FX2003 is single pack thin ﬁlm intumescent coating, designed for in-shop application by airless spray to provide ﬁre resistance for up to 120 minutes on structural steel.
Sherwin-Williams Firetex FX1003 is a single pack, thin film intumescent coating, designed for site application by airless spray, to provide ﬁre resistance for up to 120 minutes on structural steel.
International Interchar 1290 is a thin film waterborne intumescent coating optimised for hollow sections up to 180 minutes fire resistance whilst still maintaining aesthetics. Interchar 1290 is a single component, borate and chlorine free, water borne intumescent coating designed for on-site application to structural steel requiring protection...
Sherwin-Williams Firetex FX5090 is a water based TCEP free thin film intumescent coating, designed for application by airless spray to provide fire resistance for periods of up to 120 minutes on structural steel.
International Interchar 2090 is a single component, solvent borne, borate free, high solids, low VOC intumescent coating designed to maintain your architectural aesthetics whilst providing fire protection for up to 120 minutes for columns, I-sections, cellular beams and hollows.
Sherwin-Williams Firetex M72 is a solvent based intumescent mastic coating, used for the repair of small areas of mechanical damage to Firetex range of intumescent coatings.
Nullifire TS815 Solvent-Based Acrylic Top Seal is a single pack, high build modified acrylic topseal conforming to 2010 VOC limits. This product is designed for use with the Nullifire System S range of intumescent basecoats.
Jotun Steelmaster 60WB is a one component waterborne acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to cellulosic fire. ADVANTAGES Best loadings for beams and columns Low VOC, water-borne Single coat application for a majority of 60minute steel sections Low odour Tested to...
Zeroflame Aquasteel WB+ is a White Intumescent Coating that is ideal for smaller fireproofing jobs on steel. ADVANTAGES Achieves 30 & 60 mins' fire resistance on structural steel profiles Tested to internationally accepted standards BS476 Parts 20 & 21 Certificate application included Fast drying Apply by brush, roller or...
Thin film water-borne intumescent coating optimized for 90 and 120 minutes fire resistance, as part of the Interchar range for cellulosic fire protection, International Interchar 1190 will maintain your architectural aesthetics for fire resistance periods up to 120 minutes on structural steelwork.