Envirograf Mordant Solution
  • Envirograf Mordant Solution

Envirograf Mordant Solution

Product 83

Mordant Solution is part of the Intumescent Coating for Steel & Aluminium Protection range, helping protect steelwork with extra fire protection.

  • Prepares galvanised steel prior to coating
  • Treats approx. 15 square metres per litre
  • Available in 1L to 5L quantities
VAT excluded

£32.33 Tax incl.


Envirograf Mordant Solution, part of the Intumescent Coating for Steel & Aluminium Protection range. Prepares and pre-treats galvanised steel before applying protection coatings.


Ensure any oil and grease is removed from the surface to be treated. Allow the surface to dry before application of subsequent coating.

Thoroughly work Mordant Solution into the surface using a brush ensuring all the surface changes colour (blackens). If no initial reaction takes place, then a second application may be required. Rinse with clean water and allow to dry.

  • Coverage: Mordant Solution will treat approximately 15 square metres per litre
  • Drying Time: 30 minutes minimum – 24 hours maximum.
  • Thinner: not applicable
  • VOC Content: not applicable
  • Film Thickness: not applicable


  • Irritating to eyes
  • Contains: Propan-2-ol
  • Use only in well ventilated areas
  • Vapours may cause drowsiness and dizziness
  • Avoid contact with skin and eyes
  • In case of contact with eyes, rinse immediately with plenty of water and seek medical advice
  • After contact with skin, wash immediately with plenty of water
  • Wear suitable protective clothing, gloves and eye/face protection
  • If swallowed, seek medical advice immediately and show the container or label
  • Keep out of the reach of children.

IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and ConditionsWe will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
Product 83

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Be the first to ask a question about this product!

Question about the product

* Required fields
16 other products in the same category:

Jotun Penguard Express ZP

Jotun Penguard Express ZP is a two component amine cured epoxy coating that is a fast drying, zinc phosphate pigmented, high solids, high build product. Specially designed for new construction where fast dry to handle and over coating times are required. Can be used as a primer, mid coat, finish coat or as a single coat system in atmospheric...

Price £40.28
In stock

Nullifire PM015 Aluminium Epoxy Primer

Nullifire PM015 Aluminium Epoxy Primer is a high-build, low temperature curing modified aluminium epoxy mastic. Nullifire PM015 provides unequaled levels or barrier protection and corrosion resistance over existing finishes and rusted or St2/St3 cleaned steel.

Price £89.40
In stock

Envirograf HWAP/WB Primer

Envirograf HWAP/WB Primer is a clear water based primer:  For use under Envirograf HW01 and HW02E Intumescent coatings Can be applied over existing paint systems or wood stains to improve adhesion of the fire protection coating to the substrate Application by brush or roller

Price £26.24 Regular price £29.16
In stock

Sherwin-Williams FIRETEX C69

Sherwin-Williams FIRETEX C69 is a two pack epoxy, fast-track blast primer for intumescent coatings. It is a fast-track temporary protective coating for surfaces prepared by abrasive blast cleaning, designed for use under FIRETEX intumescent coatings.

Price £175.82
In stock

Nullifire PM021 General Purpose Epoxy Primer

Nullifire PM021 General Purpose Epoxy Primer is a two-components epoxy polyamide primer with excellent resistance to salts, water and alkalies, and with very good resistance to mild acids and solvents. 

Price £252.45
In stock

Sherwin-Williams Macropoxy 400

Macropoxy 400 (formerly known as Sherwin-Williams Macropoxy C400V3) multi-functional epoxy zinc phosphate coating is suitable for the protection of steelwork in a range of exposure environments from C1 to C5. It was recently used on The Shard for corrosion protection. Recommended Uses Buildings Car parks Petrochemical plants Breweries...

Price £58.12 Regular price £64.58
In stock

Thermoguard High Build Metal Primer

Thermoguard High Build Metal Primer is the compatible, corrosion-resistant primer recommended for use on suitably prepared steel prior to the application of Thermoguard Thermocoat W. ADVANTAGES High build Quick dry Corrosion resistant Solvent-based Protects during construction

Price £26.00
In stock

Nullifire PM019 Primer for Blasted Steel Substrates

Nullifire PM019 Primer for Blasted Steel Substrates is an anti-corrosive transport primer for temporary protection of blasted steel substrates, which will be finished with a compatible basecoat. Applied at standard film thickness, the protection in outdoor conditions is limited to approximately 3 months. Within this period of time the...

Price £313.56
In stock

Thermoguard Flame Retardant WB Primer

Thermoguard Flame Retardant WB Primer, a water-based primer for application to structural steel and cast iron prior to overcoating with Thermoguard Thermocoat W and Thermoguard Flame Retardant WB Topcoat. Quick drying primer for Thermoguard anti-fire system - refer below for system specification Water-based Assists in the control of...

Price £26.00
In stock

Jotun Pilot QD Primer

This is a primer from Jotun that can be applied to steel, aluminium or wood, and features very good adhesion properties on all these substrates. Jotun Pilot QD Primer is an anti-corrosive one component oxidatively drying alkyd coating that is a fast drying, high build, zinc phosphate pigmented product.

Price £26.33
In stock

Thermoguard Flame Retardant WB Topcoat

Thermoguard Flame Retardant WB Topcoat, a a quick drying, dual-purpose water-based flame-retardant paint for use over Thermoguard Thermocoat W for 30 or 60 mins Class O fire rating on on-combustible or intumescent protected surfaces. Protects intumescent paint and helps control the spread of flames For 30 or 60 mins refer to Thermocoat...

Price £52.00
In stock

Hydron Nu-Flame HB Metal Primer

Nu-Flame HB Metal Primer is ideal for priming cast iron and structural steel in preparation to apply the Nu-Flame Fire Retardant System for metals. Advantages Quick dry. Ideal for cast iron and structural steel. 8m²/Litre coverage. 3 colours available. 12-month shelf life.

Price £57.75
In stock

Nullifire PM018 Primer or Top Seal Epoxy Coating

Nullifire PM018 Primer or Top Seal Epoxy Coating is a two-components modified epoxy coating. It is a heavy duty, high build coating for protection of steel in corrosive environments and is excellent for use at low temperatures. 

Price £311.85
In stock

Envirograf HW04 Undercoat

Envirograf HW04 Undercoat is a white water based undercoat for use over Envirograf HW01 White Intumescent Coating before applying any proprietary top coat or Envirograf HW Acrylic Top Coat.

Price £20.32 Regular price £22.58
In stock

Bollom Flameguard Ultra Primer / Undercoat

Bollom Flameguard Ultra Primer/Undercoat is for application prior to the use of Bollom Flameguard Ultra Topcoats on bare and previously painted non-combustible surfaces. ADVANTAGES Excellent adhesion Seals porous surfaces

Price £62.21
In stock