Thermoguard Flame Retardant Anti-Graffiti Bond & Colour Coat is an anti-graffiti, decorative, flame retardant coating for bare & painted walls. It is a water-based, high durability two-pack coating, designed to enable removal of graffiti through use of graffiti removers.
Also available with Thermoguard Flame Retardant Anti-Graffiti Clear Glaze as part of the Thermoguard Flame Retardant Anti-Graffiti BS Class 1/0 & EN Class B System. The Bonding Primer Colour Coat provides excellent adhesion & opacity. The Clear Glaze provides exceptional resistance to oils, inks, crayon, marker and spray paints
When used in conjunction with Thermoguard Flame Retardant Anti-Graffiti Clear Glaze, 1 coat of each combine to upgrade high-flamespread-risk “multilayer” painted walls to Class O and Class B s1 dO.
Thermoguard Flame Retardant Anti-Graffiti Bond & Colour Coat contains high grade fade-resistant coloured pigments & adhesion promoters.
Quick Links - Click To Jump To Section:
Features & Benefits
Colour Range & Finish
- Thermoguard Flame Retardant Anti-Graffiti Bond & Colour Coat - Clear, White, BS 4800 + RAL wall colours
- Thermoguard Flame Retardant Anti-Graffiti Clear Glaze - Clear finish applied over Bonding Primer Colour Coat
Fire Test Standards
BS 476 Parts 6 + 7 Class O and Class B s1 dO
To bare, painted & multi-layer painted walls:
Available Systems
Available as part of the Thermoguard Flame Retardant Anti-Graffiti BS Class 1/0 & EN Class B System.
Surface Preparation
- Surfaces should be clean, dry & free from contamination
- Existing paint must be firmly adhered
- Abrade old Anti-Graffiti or other hard, smooth, impermeable paints with 120 grit abrasive to get a good key & dust off
- Ensure good ventilation and do not apply if condensation may occur
- Seal bare areas with 1 coat thinned 5% with water
Application
- Apply by brush, roller or spray
- Air min. 10°C, surfaces min 3°C above dew point during application & drying
- Stir base and activator thoroughly, then mix, stirring to create a homogenous mix (a paint stirrer on an electric drill is recommended)
- Pot life once mixed 2 hours
Apply:
- 1 coat Thermoguard Flame Retardant Anti-Graffiti Bonding Primer Colour Coat. Note: 2 coats MUST be applied on bare surfaces or contrasting colours
- 1 coat Flame Retardant Clear Glaze
Composition
- Bonding Primer Colour Coat – High grade fade-resistant coloured pigments & adhesion promoters
- Clear Glaze – High durability scrub, Flame Spread & Chemical Resistant Resin
Both are water-based.
Curing
Curing Times @20°C |
Touch dry |
4hrs |
Hard Dry |
8-12hrs |
Full Cure |
7-10 Days |
Minimum Overcoating Time |
24hrs |
Maximum Overcoating Time |
72hrs |
Colder temperatures or high humidity delay dry, cure & hardening.
Storage
- Store in tightly closed original container in a dry, cool and well-ventilated place
- Store in closed original container at temperatures between 5°C and 25°C
- Protect from freezing and direct sunlight
- Keep upright
Coverage
- A 5kg pack typically covers 40m² when applied in a single coat
Project Fire Certificate
- Thermoguard issue a Fire Certificate for completed projects for property managers to demonstrate Duty of Care compliance. Click here to apply
Health & Safety
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.