OrEnvirograf Stabond Stabilising Bonding/Sealing Liquid is a transparent water based bonding/sealing liquid for porous/friable surfaces such as plaster ceilings or walls (to seal the surface over old flaky plaster or new plaster) and to seal wood when using Product 38 Intumescent Material for door upgrades.
Envirograf Stabond Stabilising Bonding/Sealing Liquid is solvent free and supplied ready to use. The product has been designed to be readily absorbed to form a stable surface finish for application of fire retardant coatings, emulsions, varnishes and adhesives (including double-sided tape). Good for sealing prior to using Product 38 (included in door upgrade kits), Product 92 Coating System for wood, Product 105 (EP/CP paint for plasterboard) and Product 84 (Fireproof Paper)
Preparation of existing painted or varnished doors:
Wash the doors down with detergent water and clean off with warm, clean water. Ensure that all wax and grease has been cleaned off. An Envirograf de-waxing fluid is available if required. Rub all the panels with coarse glass paper and be certain to dust off and remove all flaking varnish and ensure all corners are given a good key, then apply one coat of Envirograf Stabond Stabilising Bonding/Sealing Liquid.
Tack free time: Approximately 10 minutes depending on surface type, temperature and humidity.
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contactedto obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Nu-Flame Heat Insulating Basecoat is designed to insulate flammable paint systems and control surface spread of flame and fire propagation.
Undercoat for the Nu-Flame System.
Insulates from heat and oxygen.
12-month shelf life.
Envirograf HW02E Clear Intumescent Coating upgrades the fire resistance of new and certain already coated timber and wood related surfaces.
For internal/external use
BS Class 0 & Class 1 and up to 60 mins fire resistance on suitable surfaces and substrates
To be used as part of a full Envirograf intumescent system...
Zeroflame Fire Retardant Treatment is for use on wood and timber:
Soaks virtually ‘invisibly’ into woods and timber
Achieves Euroclass B (BS Class 0) Fire Propagation and Spread of Flame fire protection on solid timbers
Can be overcoated for decorative purposes
For internal and external use
Certificate application included
Bollom Intulac Ultra Topcoat delivers excellent clear fire protection to wood and timber.
High performing satin or matt finish
To be applied over Bollom Intulac Ultra Basecoat to complete a Class 0 fire-rated system
Decorative varnish system for interior use
Certificates of conformance & installation available
Thermoguard Thermoproof Exterior Fluid is a penetrating fire proof fluid for bare wood such as sleepers, fencing, cladding and decking. The weather resistant, water-based, non flammable formula enables safe application by untrained and inexperienced users.
Envirograf ES/VFR Primer is a water-based clear primer to apply over existing paint or varnish surfaces before applying subsequent compatible fire protection systems to improve compatibility and adhesion with various substrates.
Thermoguard Thermoproof Interior Sealer is available in a matt or satin finish and is used as a protective coat to be applied over Thermoguard Thermoproof Interior Fluid where protection from wear, damp & UV resistance is required. Thermoguard Thermoproof Interior Sealer is available in clear or woodstain colours.
Thermoguard Sprayshop Lacquer Topcoat, a hard, wear-resistant Fire Protection AC lacquer for application by professional lacquer sprayers in spraybooths. Provides intumescent fire protection (Class B s2 dO + Class O) to timber surfaces.
Available in woodshades and 350+ colours from RAL and BS
Quality assurance - Manufactured under ISO 9000...
Thermoguard Timbercoat is a durable fire protection paint for interior and exterior timber surfaces:
Meets new Fire Regulations standard:
BS EN Class B s1 d0, BS Class 1
Class O Surface Spread of Flame
Can also achieve 30 & 60 minutes Fire Resistance in certain instances
Expands to create a barrier, insulating wood from heat and...
Envirograf ES/VFR White Fire Protection Coating is a white coloured, water based fire retardant coating for wood, and certain wood-related products:
Suitable for upgrading new and already coated timber surfaces to British Standard Class 0 & 1 and EU standard B/s1/d0
Hard wearing for internal and external use
Must always be finished...
Nu-Flame FR Anti-Bacterial Colourcoat is an Anti-Microbial finish with flame retardant properties. Protects against many commonly found bacteria (e.g. Salmonella and MRSA). Tested to BS 476 part 6 & 7 and satisfies Class ‘0’ Requirements of current Building Regulations.
Contains an active Anti-Microbial
For walls and...
Thermoguard Timbercoat 30 and 60 Minute System is a coloured intumescent paint system for interior and exterior timber surfaces. Each pack contains the correct amount of basecoat (Timbercoat) and topcoat (Smoke and Flame Retardant Dualcoat) to ensure protection is achieved inline with the manufacturers recommendations to the respective area in...
Thermoguard Wallcoat BS Class 1/0 & EN Class B System is a coloured fire retardant paint system for interior plasterboard ceiling and wall surfaces. Each pack contains the correct amount of basecoat (Wallcoat) and topcoat (Wallcoat Smoke & Flame Retardant Topcoat) to ensure protection is achieved inline with the manufacturers...
Nu-Flame SP Multi Surface Primer is a white water-soluble primer that forms part of the Nu-Flame Fire Upgrade System.
Suitable for glass, tile, melamine and powder coating.
Thermoguard Fire Varnish 30 and 60 Minute System is a clear intumescent varnish for interior and exterior timber surfaces. Each pack contains the correct amount of basecoat (Fire Varnish Basecoat) and topcoat (Fire Varnish Overcoat (Interior) / (Exterior)) to ensure protection is achieved inline with the manufacturers recommendations to the...
Zeroflame Fire Retardant Paint is a matt white, single-pack waterborne coating for wood, and other wood derivatives that achieves Class 1 and Class 0.
Achieves the equivalent to Class 0 and Class 1 to EU Standard EN13501-1:2007
Can be over-coated with waterbased latex paints
Coverage rate of 3.7m² per litre
Certificate included in each...