• On sale!
Envirograf HW02E Clear Intumescent Coating
  • Envirograf HW02E Clear Intumescent Coating

Envirograf HW02E Clear Intumescent Coating

Product 42 - HW02E

Envirograf HW02E Clear Intumescent Coating upgrades the fire resistance of new and certain already coated timber and wood related surfaces.

ADVANTAGES

  • For internal/external use
  • BS Class 0 & Class 1 and up to 60 mins fire resistance on suitable surfaces and substrates
  • To be used as part of a full Envirograf intumescent system
  • Water-based
Colour
Size
£36.33
£32.70 Save 10%
VAT excluded

£39.24 Tax incl.
Quantity

Description

Envirograf HW02E system offers a clear, intumescent coating, for upgrading new and certain already coated timber and wood related surfaces (contact the Technical Department to check the suitability of your substrate). Envirograf HW02E Clear Intumescent Coating is to be used as part of a complete system including selected primers and topcoats and is a water based product that can be used internally and externally to provide BS Class 0 & Class 1 as well as up to 60 minute protection for wood and certain wood related products (see product data sheets and test data (available upon request) for full details).

Preparation & Application

See product data sheets in the 'Attachments' section below.

DOORS - Please see Envirograf Door Upgrade Varnish System.

Notes:

  • Envirograf HW02E Clear Intumescent Coating needs to be upturned for 4 minutes, then add 5% water and stir thoroughly for five minutes. In cold weather it can go slightly thick, stand the container in hot water and stir it well – it will then go to a paint consistency. When applying Envirograf HW02E Clear Intumescent Coating ensure then area is warm and dry, NOT COLD & DAMP.
  • The shelf life is 6 months from batch date.
  • Envirograf HW02E Clear Intumescent Coating cannot provide 30 or 60min protection on man-made timbers such as MDF, OSB, Plywood, etc. only BS Class 0 & Class 1.
  • Minimum timber thicknesses apply for 30min and 60 minute protection - consult the product data sheets, test reports and Technical Department before proceeding.
  • Seek approval from the relevant authority for this product/system including test data prior to purchase/use (test data available upon request).

IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and ConditionsWe will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
Product 42 - HW02E

Data sheet

Application
Brush, Roller, Spray
Touch Dry
1 - 2 Hours
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Wayne Harris on 19/05/2019
Question: 

Hi, We have a busy occupied office with approximately 120sq m of old wooden floorboards (height 3m X length 40m ) that have been mounted on the walls and finished with 2 costs of Dulux Antique White vinyl Matt emulsion.They are purely decorative. We are looking for a clear fire retardant product that we can apply to the mounted floorboards in order that we can keep the original colour showing through.We have to bear in mind that the office will be occupied while decoration is carried out. Is this product suitable and is it a one coat process? Kind regards Wayne Harris

Answer: 

We would not recommend a clear system is applied over this as it will discolour/obscure the finish you wish to keep. Instead we would recommend applying 2 coats of Zeroflame Fire Retardant Paint which once dry can either be left as a white matt finish or overcoated with waterborne latex paints, applied at a total dry film thickness not exceeding 35 microns.

Based on 120m² you would require 7 x 5lts of Zeroflame Fire Retardant Paint to apply the required two coats.

questions Kevin Sutcliffe on 01/04/2019
Question: 

Can I apply normal coloured varnish over the top of your clear satin top coat?

Answer: 

Once the Envirograf system has been applied you can over coat with a topcoat of your choice. Envirograf recommend carrying out a small test area first to ensure compatibility between coatings. Envirograf advise this will have no detrimental effect on the fire rating properties of their product.

questions Simon on 05/03/2019
Question: 

Hi, We're fitting timber cladding (18mm thick larch) to our extension and the building inspector says it needs to be 30 minute fire rated. Which one of your products is clear and would achieve this? The building inspector is concerned that any sprayed applied finish will deteriorate as it's external cladding and open to the elements. Any advice you can give me would be greatly appreciated. Thanks, Simon

Answer: 

Envirograf advise to achieve a 30 minute fire rating they would recommend the use of their product 42 HW System. They have advised this product system will last the life of the substrate as long as no damage to the coating occurs, for external use they recommend re-applying the topcoat every 3-5 years for maintenance purposes. Please see the following specification:

questions Charlotte on 03/02/2019
Question: 

Can this be used on kitchen worktops?

Answer: 

No, the product we recommend for kitchen worktops is Rust-Oleum Worktop Transformation Kit, however this offers no fire protection.

questions Benjamin Hansen on 07/12/2018
Question: 

Can this product be applied to substrates other than wood? I.E. plastics or composite materials that are non-porous?

Answer: 

We would only recommend Envirograf HW02E Clear Intumescent Coating for upgrading new and already coated, internal and external timber and wood related surfaces as per the product data sheet.

questions Miles Falkingham on 25/10/2018
Question: 

Can I use this product to give 30mins fire resistance to exposed poplar floor joists instead of allowing additional timber for charring? Thanks Miles

Answer: 

For 30 minutes protection the dimensions of the joists will need to exceed 25mm x 100mm, if your joists are suitable Envirograf advise;

questions Jim Norris on 24/08/2018
Question: 

Hi, I have a panelled tongue & groove timber staircase wall. It is already coated with a water based clear varnish. Just checking that I will be doing it correctly and providing the correct fire safety. Do I need to just sand it down and then coat it with your intumescent clear varnish, or is there a lot too it please? Sorry to be a pain in !!!! Jim

Answer: 

To enable us to answer your queries we will need as much of the following information as possible;

  • Size of surface area to protect
  • Timber thickness
  • Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
  • Type of timber (i.e. pine, mdf, plywood, etc.)
  • Internal or external
questions Clive Griffiths on 31/07/2018
Question: 

How long between coats Envirograf primer - 1 coat Envirograf HW02 - 3 coats Envirograf HW Superb 2 coats. applied to new cedar cladding. Thank you

Answer: 

In good drying conditions (20°C/50% r.h.) we expect the following overcoat times; Envirograf HWAP/WB Primer - After 1 hour, Envirograf HW02E Clear Intumescent Coating - After 2 hours and Envirograf HW Superb Clear Top Coat - After 1 hour.

questions Harry Watts  on 12/02/2018
Question: 

How regularly should the Envirograf intumescent wood treatment be applied ? Kind regards Harry

Answer: 

Envirograf HW02E Clear Intumescent Coating should be used as part of a complete system (primer, intumescent and topcoat), the system will remain effective for the life of the substrate as long as it is regularly inspected and maintained in good condition. If any coating gets damaged, you must retreat the area immediately to maintain the fire rating. 

  

Question about the product

* Required fields
(read)
Send
16 other products in the same category:

Envirograf QVFR Clear Fire Protection Coating

Envirograf QVFR Clear Fire Protection Coating is suitable for upgrading new and already coated timber and wood related surfaces to BS Class 0 & 1 and EU standard B/s1/d0. ADVANTAGES Achieves BS Class 1 & 0 Achieves SBI:B/s1/d0 Low cost system Easy and safe to apply Long term protection

Price £22.72 Regular price £25.24
In stock

Envirograf HWAP/WB Primer

Envirograf HWAP/WB Primer is a clear water based primer:  For use under Envirograf HW01 and HW02E Intumescent coatings Can be applied over existing paint systems or wood stains to improve adhesion of the fire protection coating to the substrate Application by brush or roller

Price £26.24 Regular price £29.16
In stock

Envirograf QVFR White Fire Protection Coating

Envirograf QVFR White Fire Protection Coating is for wood and certain wood related products. It is suitable for upgrading new and already coated timber and wood related surfaces to British Standard Class 0 & 1 and EU standard B/s1/d0. It leaves a matt white finish, in instances where the coating may be subject to damage or high humidity a suitable...

Price £27.75 Regular price £30.83
In stock

Bollom Broflame Ultra Basecoat

Bollom Broflame Ultra Basecoat is a decorative, thin film intumescent base coat that delivers a Class 0 rating over solid timber and particle boards when used in conjunction with Bollom Flameguard Ultra Topcoats. ADVANTAGES Achieves Class 0 fire protection rating to BS476: Parts 6 and 7 Hard wearing protective/decorative finish...

Price £79.20
In stock

Thermoguard Timbercoat

Thermoguard Timbercoat is a durable fire protection paint for interior and exterior timber surfaces: Meets new Fire Regulations standard: BS EN Class B s1 d0, BS Class 1 Class O Surface Spread of Flame Can also achieve 30 & 60 minutes Fire Resistance in certain instances Expands to create a barrier, insulating wood from heat and...

Price £103.00
In stock

Bollom Intulac Ultra Basecoat

Bollom Intulac Ultra Basecoat is a clear, high-performance fire protection varnish coating for interior wood surfaces. ADVANTAGES Can be applied over existing varnish Simple 3 coat system to achieve Class 0 Single pack products No mixing required Protects and highlights natural beauty of the wood For interior use  Diminishes flue-gas...

Price £156.33
In stock

Thermoguard Flame Retardant Anti-Graffiti Clear Glaze

Thermoguard Flame Retardant Anti-Graffiti Clear Glaze is an exceptionally smooth, hard and impermeable clear two-pack flame retardant coating for internal and external use. It is a water-based, high durability two-pack coating system, designed to enable removal of graffiti through use of graffiti removers. The chemically cured coatings provide excellent...

Price £125.00
In stock

Envirograf EP/CP Fire Protection Coating

Envirograf EP/CP is a white fire protection coating for plasterboard and lath-&-plaster ceilings of various thicknesses:  BS Class 0 & 1, EU standard B/s1/d0 & up to 60 minutes' protection Develops a microporous intumescent layer with a smooth decorative finish When attacked by fire, the intumescent material protects the coated area’s integrity &...

Price £27.15 Regular price £30.17
In stock

Envirograf ES/VFR Primer

Envirograf ES/VFR Primer is a water-based clear primer to apply over existing paint or varnish surfaces before applying subsequent compatible fire protection systems to improve compatibility and adhesion with various substrates.

Price £26.85 Regular price £29.83
In stock

Hydron Nu-Flame FR Anti-Bacterial Colourcoat

Nu-Flame FR Anti-Bacterial Colourcoat is an Anti-Microbial finish with flame retardant properties. Protects against many commonly found bacteria (e.g. Salmonella and MRSA). Tested to BS 476 part 6 & 7 and satisfies Class ‘0’ Requirements of current Building Regulations. Advantages Flame retardant Contains an active Anti-Microbial For walls and...

Price £93.25
In stock

Zeroflame Fire Retardant Paint

Zeroflame Fire Retardant Paint is a matt white, single-pack waterborne coating for wood, and other wood derivatives that achieves Class 1 and Class 0. Achieves the equivalent to Class 0 and Class 1 to EU Standard EN13501-1:2007 Can be over-coated with waterbased latex paints Coverage rate of 3.7m² per litre Certificate included in each...

Price £89.99 Regular price £99.99
In stock

Thermoguard Flame Retardant Anti-Graffiti Bond & Colour Coat

Thermoguard Flame Retardant Anti-Graffiti Bond & Colour Coat is an anti-graffiti, decorative, flame retardant coating for walls. It is a water-based, high durability two-pack coating system, designed to enable removal of graffiti through use of graffiti removers. The chemically cured coatings provide excellent resistance to oils, inks and spray paints.

Price £125.00
In stock

Envirograf HW01 White Intumescent Coating

Envirograf HW01 is a white, intumescent coating for wood. ADVANTAGES  BS Class 0 & Class 1 protection 30 & 60 mins’ fire resistance White finish for upgrading new or previously coated wood & timber Water-based for internal/external use Should be used as part of a complete Envirograf system

Price £30.68 Regular price £34.09
In stock

Envirograf ES/VFR Clear Fire Protection Coating

Envirograf ES/VFR is a Clear Fire Protection Coating for wood and timber. ADVANTAGES British Standard Class 0 & 1 and EU standard B/s1/d0 Water-based for internal/external use Can be used as part of an economically priced Envirograf system Easy and safe to apply Delivers long-term protection and fire resistance Also available in a white finish

Price £25.71 Regular price £28.57
In stock

Thermoguard Thermoproof Interior Fluid

Thermoguard Thermoproof Interior Fluid is a clear, colourless, penetrating Fire Protection with an optional functional Thermoguard Thermoproof Interior Sealer for wear, damp & UV resistance available in clear or woodstain colours.

Price £89.00
In stock

Hydron Nu-Flame Clear Overcoat

Nu-Flame Clear Overcoat is a clear varnish finish coating with flame retardant qualities for application onto timber surfaces. Tested to BS476 Part 7 Class 1 surface spread of flame and BS476 Part 6 Fire propagation. Advantages Protects against humidity, heat and wear and tear Satin and Gloss finishes available 12m²/Litre coverage

Price £95.00
In stock