Bollom Flameguard Ultra Vinyl Matt is a top coat for Bollom Broflame Ultra Basecoat on bare and previously painted wood and Bollom Brosteel Ultra 60 Hard wearing vinyl matt finish Top coat for Bollom intumescents for wood and steel Provides Class 0 on non-combustible surfaces Available in 4,100+ colours, including RAL, BS and NCS...
Bollom Broflame Ultra Basecoat
Bollom Broflame Ultra Basecoat is a decorative, thin film intumescent base coat that delivers a Class 0 rating over solid timber and particle boards when used in conjunction with Bollom Flameguard Ultra Topcoats.
Features and Benefits
- Achieves Class 0 fire protection rating to BS476: Parts 6 and 7
- Hard wearing protective/decorative finish
- For all types of timber in communal areas
**Available for delivery - see Delivery Options below**
Bollom Broflame Ultra Basecoat
Bollom Broflame Ultra Basecoat is ideal for all types of interior timber in communal areas.
- Solid timber
- Timber-faced boards
- Particle boards
- Communal interior timber
- Public buildings
Together with one of the Bollom Flameguard Ultra Topcoats this system provides a means of achieving your desired colour scheme and finish, whilst providing Class 0 on the painted surface. The paints are designed to inhibit surface spread of flame and heat release, providing vital escape time in the event of a fire.
NOTE:It is important to speak to our Technical Department and refer to the product data sheet prior to using this product to ensure the correct specification has been chosen for your surface.
Ensure the surface to be painted is sound, clean, dry and free from grease or any substance liable to give adhesion problems. Treat any knots. Scrape off any old or flaking paint until you have a firm well adhered surface; if in doubt remove all existing coatings. For existing gloss and eggshell finishes wet abrade and rinse with clean water to remove any residues.
- Stir well before use.
- Applied by brush or airless spray, can be applied by roller but must be subsequently laid off with a brush to achieve a smooth finish.
- Bollom Broflame Ultra Basecoat must not be thinned.
- Coverage rates must be adhered to in order to achieve the Class 0 upgrade.
- Apply two coats @ 5m² per litre/per coat taking care to avoid runs or sags allow at least 4 hours between coats. After the second coat leave 24 hours before applying Flameguard Ultra Top coats.
How do I get Fire Certification?
To obtain the completed certificates for a project customers should email [email protected] with the following details:
- Proof of purchase
- The contractors/applicators name and contact details (tel. no, email, address)
- Batch number(s) of product(s) used
- Site address
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
- Brush, Roller, Spray
- 5m² per litre
- Touch Dry
- 4 Hours
|pete duffy on 2018-11-13 16:24:22|| |
We are currently carrying out a shop fit using 18mm MDF fixed to 75 x 50 CLS timber studding The finish IS lining paper, then 2 coats of washable white matt emulsion Building Inspector said he would accept am intumescent paint What do you recommend Doors and door frames are FD30
Could you confirm the level of fire protection you are being asked to achieve on the MDF please? This is extremely important to ensure we provide the correct advice/product. Also, do you know how many square metres there will be to paint?
Bollom Flameguard Ultra Primer/Undercoat is for application prior to the use of Bollom Flameguard Ultra Topcoats on bare and previously painted non-combustible surfaces. ADVANTAGES Excellent adhesion Seals porous surfaces Coverage Calculator More Information **Available for delivery - see Delivery Options below**
Bollom Flameguard Ultra Acrylic Eggshell is a top coat for Bollom Broflame Ultra Basecoat on bare and previously painted wood, and Bollom Brosteel Ultra 60 for steel. ADVANTAGES Hard wearing eggshell finish Top coat for Bollom intumescents for wood and steel Provides Class 0 on non-combustible surfaces Available in 4,100+ colours,...
Bollom Flameguard Ultra Gloss is a top coat for Bollom Broflame Ultra Basecoat on bare and previously painted wood, Bollom Brosteel Ultra 60 and Bollom Fireshield Ultra Universal for steel. ADVANTAGES Hard wearing gloss finish Top coat for Bollom intumescents for wood and steel Provides Class 0 on non-combustible surfaces Please note:...
General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site. Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects Click to jump down to...