503 Easy Clean Anti-Slip Coating is a two-pack solvent-free, high-build epoxy resin coating containing a hard wearing fine particle anti-slip additive that is pre-dispersed into the resin and held in suspension.
Low odour
Excellent adhesion to concrete and steel
Even, fine textured finish
Tough, durable and easily applied
Also available in 4000+ RAL, NCS, and British Standard colours
503 Easy Clean Anti-Slip Coating is a two-pack solvent-free, high-build epoxy resin coating containing a hard wearing fine particle anti-slip additive that is pre-dispersed into the resin and held in suspension. The result provides a ‘ready to use’ product that leaves an evenly textured, slip resistant surface that is easy to clean and is extremely durable.
503 Easy Clean Anti-Slip Coating will provide a heavy duty, chemical and abrasion resistant fine textured finish on concrete, steel and other substrates. Applied by roller and paint brush the product is low odour producing a seamless, hard wearing, hygienic floor finish.
Note: We recommend using 502 HD Anti-Slip Coating on ramps, very wet/oily areas or other areas that generally require a high level of slip resistance.
This product is for Professional Use Only.
Recommended Uses:
As a slip and chemical resistant floor coating where a less ‘aggressive’ aggregated finish is required and ease of cleaning is important
Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for specific advice.
Slip Resistance
Dry PTV: 48-50
Wet PTV: 40-42
PTV Ratings:
Slip potential classifications from Pendulum Test Values.
Slip Resistance Values
PTV
Slip Potential
< 25
High
25 - 35
Moderate
> 35
Low
The above results must only be used as a general guideline as the slip resistance of a cured resin coating can vary considerably due to many factors including: application technique, variations in film thickness, dispersion of the anti-slip texturing additive and the surface variations of the substrate and location to where it will be applied.
To obtain accurate PTV readings that are site specific (if required) it is strongly recommended that a slip assessment pendulum test is undertaken on each specific site after completion of the installation when the resin has fully cured.
A full copy of the official test report is available upon request.
Coverage
A 5kg pack is sufficient to apply one coat to 20m² of surface providing an overall d.f.t. of approximately 200 microns
Surface Preparation
Concrete:
Concrete shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%
Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound and existing paint finishes etc
Suitable mechanical treatment such as vacuum grit blasting is the preferred treatment prior to application as this ensures a mechanical ‘key’ for the coating
Steel:
Steel surfaces shall be shot blasted or grit blasted to a nominal Sa 2.5 Swedish standard
All dust and grease shall be removed prior to coating application
If a delay is likely to occur between blasting and application then it is recommended that a coat of 404 Epoxy Metal Primer is applied as holding primer to obviate flash rusting
Note: Substrates with high moisture content or oil contamination can still be coated in most instances by the inclusion of one of our specialist primers. Please see 402 Damp Proof Coating and 403 Oil Tolerant Primer for full details.
Mixing:
Pour the contents of the curing agent container into the base container and thoroughly mix, preferably by mechanical means until a uniform colour is achieved
Mixing Ratio:
By Volume - 2.44 Base: 1 Curing Agent
By Weight - 100 Base: 28.2 Curing Agent
Application
Apply by brush, roller or airless spray at a nominal rate of 0.25kg/m²
Ensure coverage rates are adhered to – spreading the product too far can result in reduced durability, performance, opacity, etc
Over application can result in reduced or even no slip resistance
This should be applied to an adequately primed or compatible (test if unsure) previously painted surfaces
Existing coatings need to be sound, free of contaminants and checked for compatibility, adequate adhesion and should be abraded to provide a suitable key for 503 Easy Clean Anti-Slip Coating to adhere
Should you wish to build the film build-up of the coating system, first apply a coat of 304 HD Epoxy Floor Coating at a nominal rate of 0.25 to 0.3kg/m²
Ensure the following coat of 503 Easy Clean Anti-Slip Coating is applied after a minimum of 14 hours and before a maximum of 48 hours
Cleaning
Clean equipment with 109 Tool Cleaner prior to curing of the coating
Curing
Allow to cure for a minimum of 24 hours @ 20°C prior to light foot traffic access and 48 hours @ 20° prior to vehicular trafficking
7 days cure @ 20°C is recommended prior to exposure to chemicals - lower temperatures will extend the curing time
Storage & Shelf Life
Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 25°C
503 Easy Clean Anti-Slip Coating has a minimum shelf life of 12 months when stored in original, unopened containers in accordance with manufacturer’s instructions
Health & Safety
Avoid contact of the material with skin and eyes
Wear gloves and goggles
Wash off splashes immediately with soap and water
Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought
503 Easy Clean Anti-Slip Coating shall be applied strictly in accordance with the manufacturer’s instructions
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
We are looking to specify Rawlins 503 503 Easy Clean Anti Slip Coating in grey and would we would be grateful if you could provide the LRV (Light Resistance Value) for the standard grey paints please?
Answer from Rawlins’ Technical Team:
We have not carried out LRV testing on the product, however we can advise the RAL colours that are close to the 3 standard greys available in this product and what the LRV is for each colour according to RAL;
Light Grey - (Close to RAL 7035) = 58.34 LRV
Mid Grey - (Close to RAL 7001) = 31.66 LRV
Dark Grey - (Close to RAL 7011) = 12.04 LRV
We obviously cannot comment on how the gloss level of 503 Easy Clean Anti Slip Coating and the aggregate contained within the coating would affect RAL's stated Light Reflectance Values but hopefully this at least provides you an approximation of what they may be near.
Should you require more exact results you would need to carry out testing on the product yourselves to obtain these. However please note that colours will change somewhat batch to batch so unless you carried out testing on the finished floor areas after they had the 503 Easy Clean Anti Slip Coating applied to them, again results may vary.
Ross McNally on 2021-06-12 10:16:36
Question:
I am looking for an outdoor paint in non slip finish. Would this finish be suitable?
Answer from Rawlins’ Technical Team:
Thank you for the enquiry, we have contacted you directly for more information.
Colin Magee on 2021-05-12 20:11:09
Question:
We have a retail shop premises with largely various female shoe traffic. The base is non-glazed ceramic tiles over which there are two coats of back general acrylic paint and two coats of white the same (yes we decided on a drastic colour change). The black seems to be pretty fast but the white layers scrape off very easily with footwear and small furniture movement. Obviously we would like to have a much more durable white finish. Will this paint be suitable, or another in your catalogue?
Answer from Rawlins’ Technical Team:
Thank you for the enquiry, assuming the previously painted cermaic tiles are clean, dry, sound and prepared as detailed in the Technical data sheet we can recommend Smartkote Protectakote UVR.
We would recommend testing for compatibility and adhesion prior to full application on previously applied coatings.
Hi - Searching for a suitable floor paint for leisure centre changing room. Will this suit?
Answer from Rawlins’ Technical Team:
This would potentially be a good option depending on the current floor type?
Please contact our Technical Team on 0113 2455450 (option 2) or [email protected] to discuss further.
lizzie on 2015-08-27 08:34:19
Question:
Can I use 503 Easy Clean Anti Slip Coating for a commercial kitchen? It needs to meet regulations which state the floor coating should be:
easy to clean
can be disinfected
non slip
durable
impervious (ie do not allow fluid to pass through)
non absorbent (do not absorb fluid)
Answer from Rawlins’ Technical Team:
Yes, 503 Easy Clean Anti Slip Coating meets all the requirements you have listed and more. You can apply in one coat to previously painted surfaces (ensure compatibility with a test area) or floors primed with 401 Epoxy Floor Primer / 304 HD Epoxy Floor Coating.
503 Easy Clean Anti Slip Coating is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
201 Epoxy Repair Mortar is a high strength, trowel applied, two component epoxy resin mortar, designed for rapid and permanent repairs to concrete and masonry surfaces.
Pre-packed units – ready to use
Fast curing
Impact and abrasion resistant
Frost resistant and impervious to water
Negligible shrinkage
Images are for illustrative...
403 Oil Tolerant Primer has been developed for use in applications to oil contaminated floors prior to application of subsequent floor toppings. The product exhibits outstanding adhesion to concrete and other substrates and is particularly suitable where compromised surfaces exist.
Solvent free, low odour
Excellent adhesion to concrete and...
404 Epoxy Metal Primer is a two pack, water-based, epoxy, anti-corrosive primer designed for the protection of steelwork.
Non toxic
Fast drying - touch dry in 1-2 hours @ 20ºC
May be applied to damp or dry surfaces
Excellent anti-corrosive properties
Compatible with a wide range of top coats
Long overcoating window
Easily applied...
We no longer stock this product, but can recommend 304 HB Epoxy Floor Coating as a great alternative.
304 HD Epoxy Floor Coating is a two-pack solvent free high-build epoxy resin system for application as a heavy duty floor coating for concrete, steel and other substrates.
Low odour - Very good chemical resistance - High build
Excellent...
502 HD Anti Slip Coating is a 3-pack solvent-free high-build epoxy resin system for application as a heavy duty non-slip floor coating for concrete, metal and wood surfaces requiring high levels of slip resistance.
Tough, long lasting high-build finish
Virtually odourless
Easy to apply and good colour stability
Hygienic and good chemical...
109 Tool Cleaner is a specialist equipment cleaner suitable for the removal of uncured epoxy, polyester and polyurethane resins.
Low Hazard
Low evaporation rate
Excellent solvency powers
80% biodegradable
This product is for Professional Use Only
Images are for illustrative purposes only and may differ from the actual product
More...
402 Damp Proof Coating is a two pack epoxy resin based primer/coating, which has been developed to function as a residual construction moisture suppressant, allowing the early installation of moisture sensitive flooring in fast track building programmes.
Also available in 4,000+ colour options from RAL, BS and NCS
Please see 402 Damp...
Steven Cromb on 2022-04-21 16:22:43
