Britannia Walkway Safety Coating is based on an acrylic MMA copolymer. It provides a hard, tough, flexible and easy to apply film coating with excellent external durability and resistance to heat and alkaline conditions. It also contains polymer beads with outstanding slip resistance.
Ready for use over concrete and asphalt. Can be applied by brush or roller.
Provides a hard, tough, flexible and easy to apply film coating
Excellent external durability
Resistance to heat and alkaline conditions
Outstanding slip resistance
Ready for use over concrete and asphalt
Application by brush or roller
Asphalt revival coating
Rainfall immediately after application has no adverse effect
Not a fully waterproofing system
Spreading Rate
These will vary depending on substrate, the site conditions and longevity required.
Typically spreading rates will vary depending on the end use.
Approximately 0.8kg/m2
Drying Times
Touch Dry (temperature depending): 3 – 4 hours
Full Cure – Allow 8hrs
Preparation
Clear all areas of moss, lichen and debris by brushing or power washing and remove surface water. Apply Britannia Fungicidal Wash to prevent further fungal/algal growth.
Application Temperature should be between 5°C-25°C.
Highly Porous/Friable Surfaces:
Subject to site inspection
Non-Porous Surfaces:
Subject to site inspection
Bitumen Surfaces:
Discolouration may occur over a volatile asphalt, tar or bitumen surface; therefore an extra coat may be required
Splits, Cracks, Joints and Seals:
Pay particular attention to clean out any splits/cracks/joints and seals by scraping or brushing off with a stiff bristle brush
Repair faults in the surface by embedding a polyester scrim in the first of two coats
Cut the scrim to a suitable length to ensure an overlap of the ‘fault’ by 75mm all round and embed into the first coat of Britannia Walkway Safety Coating whilst still wet, making sure to force the coating through the mesh
Crazed Areas:
Crazed areas should be filled using a suitable non-bituminous joint sealant prior to the application of a first coat
Apply a second coat to the area repaired and then over the whole area to be coated as stated below
In areas where excessive movement may occur additional reinforcement must be incorporated into the coating.
Application
Stir well before use
To the dry and cleaned surface, apply a generous coat of Britannia Walkway Safety Coating by brush or roller
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
We no longer stock this product, but can recommend Wethertex C10 Multi-Surface Fungicidal Wash as a great alternative.
Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical...
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
Colourmatch Service Disclaimer
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.