Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for specific advice.

Coverage

• 5m² per pack

Surface Preparation

Concrete:

• Concrete surfaces shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%
• Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound, and existing paint finishes etc
• Smooth concrete, or concrete with soft laitance, shall be mechanically treated by diamond grinding or grit blasting to provide a clean profiled surface
• Should this not be practicable then acid etching, although less preferable, is also an option

Metal:

• Metal surfaces shall be wire brushed or power disced to remove any rust and loose or flaking material
• Grit blasting is recommended, where practical, for optimum performance
• Coating application should be carried out immediately after preparation

Wood:

• Wood surfaces shall be sanded to a smooth finish, and all previous coating removed
• Do not add the aggregate into the mix

Note: Substrates with high moisture content or oil contamination can still be coated in most instances by the inclusion of one of our specialist primers. Please see 402 Damp Proof Coating and 403 Oil Tolerant Primer for full detail.

Mixing:

• Pre-mix the coloured base component to a uniform consistency then mix the entire contents of the base with the hardener using a slow speed electric mixer for approximately two minutes or until the two components have fully combined
• Pour the contents of the curing agent container into the base container and thoroughly mix, preferably by mechanical means until a uniform consistency is achieved

Note: If a separate mixing bucket is being used then mix thoroughly as above ensuring all contents of the 2 components are removed from the buckets supplied

Mixing Ratio:

• By Volume - 2.56 Base : 1 Curing Agent
• By Weight - 100 Base : 26.9 Curing Agent

Application

• The ambient temperatures of the areas should not be allowed to fall below 10°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system
• Surface temperature must be above 5°C
• Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation
• The mixed unit should be applied immediately by medium pile roller (not foam) or brush with a consistent procedure at an even rate of application to a measured area of no more than 5m² per pack
• Floor areas should be cross-rolled to ensure even application and to minimise roller marks
• Immediately scatter the anti-slip aggregate uniformly onto the wet coat to obtain the desired surface finish (total or light coverage as required)
• Using the same roller that was used to apply the mixed resin and hardener roll over the sprinkled aggregate to bed in and cover the anti-slip aggregate
• It is not normally necessary to re-charge the roller with mixed resin unless very heavy quantities of grit have been applied
• Coverage rates will depend on profile and porosity of the substrate
• 304 HD Epoxy Floor Coating can be installed as a first coat for a smooth finish followed by a top coat of 502 HD Anti Slip Coating for a textured finish
• Or an additional coat of 304 HD Epoxy Floor Coating can be applied (not exceeding 200 microns) over the cured 502 HD Anti Slip Coating system to increase the life expectancy of the system and make the finished surface easier to clean (please note this will most likely reduce the level of slip resistance)

Cleaning

• It is impracticable to clean rollers after use
• Clean equipment with 109 Tool Cleaner prior to curing of the coating

Curing

• Allow to cure for a minimum of 8 hours @ 20°C prior to light foot traffic access
• Curing at lower temperatures will extend this period, whereas curing at higher temperatures will allow faster access

Limitations

• Do not apply to wet or uncured concrete surfaces
• Do not apply at temperatures of 3°C or less

Storage & Shelf Life

• Store in dry conditions at temperatures between 10°C and 25°C
• Do not expose to freezing conditions
• 502 HD Anti Slip Coating has a minimum of 12 months shelf life when stored in original, unopened containers in accordance with manufacturer’s instructions

Health & Safety

• Wear gloves and goggles
• Wash off splashes immediately with soap and water
• Please refer to Material Safety Data Sheet for additional information
• 502 HD Anti Slip Coating shall be applied strictly in accordance with the manufacturer’s instructions

For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]