503 Easy Clean Anti-Slip Coating is a two-pack solvent-free, high-build epoxy resin coating containing a hard wearing fine particle anti-slip additive that is pre-dispersed into the resin and held in suspension.
Low odour
Excellent adhesion to concrete and steel
Even, fine textured finish
Tough, durable and easily applied
Available in 4,400+ colours, inc. RAL, RAL Design, BS, NCS & the new NCS 2050 colours
Readily available standard colours also available here
Ideal as a slip and chemical resistant floor coating where a less ‘aggressive’ aggregated finish is required
503 Easy Clean Anti-Slip Coating is a two-pack solvent-free, high-build epoxy resin coating containing a hard wearing fine particle anti-slip additive that is pre-dispersed into the resin and held in suspension. The result provides a ‘ready to use’ product that leaves an evenly textured, slip resistant surface that is easy to clean and is extremely durable.
503 Easy Clean Anti-Slip Coating will provide a heavy duty, chemical and abrasion resistant fine textured finish on concrete, steel and other substrates. Applied by roller and paint brush the product is low odour producing a seamless, hard wearing, hygienic floor finish.
Note: We recommend using 502 HD Anti-Slip Coating on ramps, very wet/oily areas or other areas that generally require a high level of slip resistance.
This product is for Professional Use Only.
Recommended Uses:
As a slip and chemical resistant floor coating where a less ‘aggressive’ aggregated finish is required and ease of cleaning is important
Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for specific advice.
Slip Resistance
Dry PTV: 48-50
Wet PTV: 40-42
PTV Ratings:
Slip potential classifications from Pendulum Test Values.
Slip Resistance Values
PTV
Slip Potential
< 25
High
25 - 35
Moderate
> 35
Low
The above results must only be used as a general guideline as the slip resistance of a cured resin coating can vary considerably due to many factors including: application technique, variations in film thickness, dispersion of the anti-slip texturing additive and the surface variations of the substrate and location to where it will be applied.
To obtain accurate PTV readings that are site specific (if required) it is strongly recommended that a slip assessment pendulum test is undertaken on each specific site after completion of the installation when the resin has fully cured.
A full copy of the official test report is available upon request.
Coverage
A 5kg pack is sufficient to apply one coat to 20m² of surface providing an overall d.f.t. of approximately 200 microns
Surface Preparation
Concrete:
Concrete shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%
Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound and existing paint finishes etc
Suitable mechanical treatment such as vacuum grit blasting is the preferred treatment prior to application as this ensures a mechanical ‘key’ for the coating
Steel:
Steel surfaces shall be shot blasted or grit blasted to a nominal Sa 2.5 Swedish standard
All dust and grease shall be removed prior to coating application
If a delay is likely to occur between blasting and application then it is recommended that a coat of 404 Epoxy Metal Primer is applied as holding primer to obviate flash rusting
Note: Substrates with high moisture content or oil contamination can still be coated in most instances by the inclusion of one of our specialist primers. Please see 402 Damp Proof Coating and 403 Oil Tolerant Primer for full details.
Mixing:
Pour the contents of the curing agent container into the base container and thoroughly mix, preferably by mechanical means until a uniform colour is achieved
Mixing Ratio:
By Volume - 2.44 Base: 1 Curing Agent
By Weight - 100 Base: 28.2 Curing Agent
Application
Apply by brush, roller or airless spray at a nominal rate of 0.25kg/m²
Ensure coverage rates are adhered to – spreading the product too far can result in reduced durability, performance, opacity, etc
Over application can result in reduced or even no slip resistance
This should be applied to an adequately primed or compatible (test if unsure) previously painted surfaces
Existing coatings need to be sound, free of contaminants and checked for compatibility, adequate adhesion and should be abraded to provide a suitable key for 503 Easy Clean Anti-Slip Coating to adhere
Should you wish to build the film build-up of the coating system, first apply a coat of 304 HD Epoxy Floor Coating at a nominal rate of 0.25 to 0.3kg/m²
Ensure the following coat of 503 Easy Clean Anti-Slip Coating is applied after a minimum of 14 hours and before a maximum of 48 hours
Cleaning
Clean equipment with 109 Tool Cleaner prior to curing of the coating
Curing
Allow to cure for a minimum of 24 hours @ 20°C prior to light foot traffic access and 48 hours @ 20° prior to vehicular trafficking
7 days cure @ 20°C is recommended prior to exposure to chemicals - lower temperatures will extend the curing time
Storage & Shelf Life
Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 25°C
503 Easy Clean Anti-Slip Coating has a minimum shelf life of 12 months when stored in original, unopened containers in accordance with manufacturer’s instructions
Health & Safety
Avoid contact of the material with skin and eyes
Wear gloves and goggles
Wash off splashes immediately with soap and water
Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought
503 Easy Clean Anti-Slip Coating shall be applied strictly in accordance with the manufacturer’s instructions
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
201 Epoxy Repair Mortar is a high strength, trowel applied, two component epoxy resin mortar, designed for rapid and permanent repairs to concrete and masonry surfaces.
Pre-packed units – ready to use
Fast curing
Impact and abrasion resistant
Frost resistant and impervious to water
Negligible shrinkage
Images are for illustrative...
403 Oil Tolerant Primer has been developed for use in applications to oil contaminated floors prior to application of subsequent floor toppings. The product exhibits outstanding adhesion to concrete and other substrates and is particularly suitable where compromised surfaces exist.
Solvent free, low odour
Excellent adhesion to concrete and...
404 Epoxy Metal Primer is a two pack, water-based, epoxy, anti-corrosive primer designed for the protection of steelwork.
Non toxic
Fast drying - touch dry in 1-2 hours @ 20ºC
May be applied to damp or dry surfaces
Excellent anti-corrosive properties
Compatible with a wide range of top coats
Long overcoating window
Easily applied...
We no longer stock this product, but can recommend 304 HB Epoxy Floor Coating as a great alternative.
304 HD Epoxy Floor Coating is a two-pack solvent free high-build epoxy resin system for application as a heavy duty floor coating for concrete, steel and other substrates.
Low odour - Very good chemical resistance - High build
Excellent...
502 HD Anti Slip Coating is a 3-pack solvent-free high-build epoxy resin system for application as a heavy duty non-slip floor coating for concrete, metal and wood surfaces requiring high levels of slip resistance.
Tough, long lasting high-build finish
Virtually odourless
Easy to apply and good colour stability
Hygienic and good chemical...
109 Tool Cleaner is a specialist equipment cleaner suitable for the removal of uncured epoxy, polyester and polyurethane resins.
Low Hazard
Low evaporation rate
Excellent solvency powers
80% biodegradable
This product is for Professional Use Only
Images are for illustrative purposes only and may differ from the actual product
More...
402 Damp Proof Coating is a two pack epoxy resin based primer/coating, which has been developed to function as a residual construction moisture suppressant, allowing the early installation of moisture sensitive flooring in fast track building programmes.
Also available in 4,000+ colour options from RAL, BS and NCS
Please see 402 Damp...
