Smartkote Safekote WB is a water-based, anti-slip, single component polyurethane coating with a fine texture, ideal for creating safe, anti-slip walkways, steps and ramps. Applied in a 2 coat application.
Suitable for interior and exterior use
Easy to apply - High adhesion to metal, cement, wood, fibre-glass, PVC and previously painted surfaces
Easy to clean and provides outdoor weather resistance even in marine environments
Excellent resistance to abrasion, chemicals and solvents
Smartkote Safekote WB is a water-based anti-slip polyurethane coating with a fine texture, ideal for creating safe, anti-slip walkways, steps and ramps.
It is easy to clean and provides outdoor weather resistance even in marine environments. As a single component water-based product it is easy to apply and as polyurethane it demonstrates excellent abrasion resistance and flexibility even at extremely low temperatures
Water-based - low odour, non-flammable and weather resistant
Easy to clean up – simply use water before it cures
Single component – ready to use direct from can
Easy to apply – no skilled labour required
Fast drying
Polyurethane performance – ultimate toughness
Synthetic silica particles for texture
Flexible – won’t chip, flake or peel
Excellent resistance to abrasion, chemicals and solvents
Prevents rust and corrosion with suitable primer
Excellent capacity to repel water
High adhesion to most surfaces including metal, cement, wood, fibre-glass and PVC
Can be overcoated
Repairable – bonds to itself
Will not taint water or food once cured
Product Uses
Bridges, steps and walkways
Bathrooms
Boat decks
Ramps for wheelchair access
Emergency exits and fire escapes
Anti-slip areas around machinery
On slippery floors exposed to water such as showers, change rooms and ablution blocks
Any other areas where an anti-slip coating is required (with suitable primer)
Coverage
3m² per litre per coat - Applied in a 2 coat application - Giving an overall coverage of 1.5m² per litre
Three coats are recommended for high wear areas
Coverage will vary depending on the porosity and profile of the surface
Surface Preparation
Ensure all substrates are thoroughly dry, clean, sound and free from any contaminants such as dirt, rust, salt, algae and grease. Safekote WB exhibits good adhesion to most primers. All non-porous substrates with the exception of painted surfaces require a primer. Substrates differ significantly, and so all new applications should be tested for adhesion first.
Steel:Abrade surface lightly and remove any surface rust or mill scale by sanding, wire brushing, with a chipping hammer or sandblasting. Prime withSmartkote EP90 Universal Epoxy Primeras per instructions, within 30 minutes
Galvanized Iron:Clean away grease and dirt with a suitable galvanized iron cleaner until a water break-free surface is attained. Rinse well with water and allow to dry. Abrade to provide a key and prime withSmartkote EP90 Universal Epoxy Primerthe same day as the surface was prepared to avoid re-contamination and flash rust
Concrete:Allow new concrete at least 28 days to cure. Non-porous cement must be acid-etched, rinsed well and dried. Prime withDuram Duraprimeas per instructions if weak, damp or oil contaminated
Wood:Abrade, clean and allow to completely dry before applying Safekote WB directly. Dilute the first coat with up to 10% fresh tap water to aid penetration. Dense oily woods may require a primer
Fibreglass:Abrade well, clean with detergent and apply Safekote WB directly onto the surface
PVC:Abrade and clean well using detergent. Allow to dry before applying Safekote WB directly. An adhesion test is recommended prior to use.
Gloss Paints and Varnish:Abrade with a scouring pad or medium grit sandpaper to remove all gloss. Wipe clean with water and detergent, allow to dry and apply Safekote WB directly
Painted Metal:Remove heavy dirt and rust. Previously painted surfaces need to be lightly abraded using a medium grit sandpaper to remove all gloss. Wipe clean using detergent, allow to dry and apply Safekote WB directly
Application
After substrates have been prepared, ensure they are completely dry, tests for adhesion have been completed and areas not to be coated have been masked off
Stir well before use using a flat paddle
Always apply a test patch of Safekote WB to ensure the substrate has been properly prepared and primed. Check adhesion of the coating by cutting a small X in the coating using a utility knife. Firmly apply a piece of packaging tape over the centre of the X cut, then pull off with a fast snap. The adhesion is suitable if no significant coating is removed beyond the X cut. If the coating fails this test, then additional surface preparation is required – repeat the surface preparation steps above
Brush-on:Safekote WB should be “laid” onto the surface with a brush (do not brush backwards and forwards as with an enamel paint). Two coats will result in a final dry film thickness of 0.23 - 0.25mm. Second or subsequent coats should be applied at right angles to the previous coat. Intercoat time is approximately 2 hours or when touch dry, depending on ambient conditions
Roller:If applied with a stipple roller, application is quicker and the final texture rougher with greater anti-slip characteristics. Follow same instructions as per Brush-on. Intercoat time is approximately 2 hours or when touch dry, depending on ambient conditions. Recommended roller types for Safekote WB areshort mohair roller or fine foam roller
Spray-On:Dilute Safekote WB with up to 10% of clean tap water. Fill spray gun pot, and attach airline providing a minimum pressure of 5 bar. Safekote WB should be applied inthin coatsto prevent “mudcracking” during drying. Depending on the application, two or more coats should be applied. Ensure each coat is dry before applying the next coat. Intercoat time is approximately 2 hours or when touch dry, depending on ambient conditions
Curing time:Safekote WB cures with atmospheric moisture. The coating will be touch dry in about 2 to 4 hours and allowing light traffic after 9 hours. Full strength and chemical resistance is achieved in 4 to 7 days, but normally the coating can be put to use after 24 hours
Overcoating and repair:Safekote WB can easily be repaired or overcoated. The old surface should be well cleaned and then abraded by wire brush or sandpaper, and damaged surfaces must be cut out to provide an area without loose edges. Follow application instructions. If Safekote WB is left for more than 24 hours after coating, it should be abraded before recoating to aid intercoat adhesion. If correctly applied, Safekote WB provides a seamless repair
Important Notes
All RAL colours shown for this product are approximations ONLY
Please read all instructions in the Product Data Sheet carefully before starting the project
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Smartkote Safekote WB is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Duram Duraprime is a water-based epoxy primer that treats and seals surfaces in preparation for later waterproofing. It can be used on both damp and dry surfaces and is especially effective for priming new concrete as it penetrates the surface, forming a strong, waterproof bond and allowing for easy overcoating.
Smartkote EP90 Universal Epoxy Primer, an easy to use two-pack primer for all polyurethane topcoats that provides excellent adhesion to a variety of substrates with the flexibility required for urethane.Pre-weighed components; simply add Part B to Part A and mix Exceptional bond strength to urethanes - high adhesion especially to metal...