RSL Resuprime Binder

    4268

    We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.

    RSL Resuprime Binder (formerly Resutop Binder), a low viscosity two-pack epoxy resin for defective concrete flooring and sand and cement screeds, avoiding the costs and disruption of screed replacements. The resin penetrates deeply for a resultant high strength screed, capable of meeting the stringent industrial demands required for such systems.

    • Hygienic and easily cleaned
    • Low odour
    • No shrinkage on curing
    • Excellent hard wearing finish
    • Recommended uses include food processing and beverage areas, chemical plant rooms, engineering workshops, automotive & aviation areas, factory units and warehouses
    • Please note there is currently a minimum purchase quantity of 60 units required

    Quantity
    Product not available
    This Product has been Discontinued

    Description

    We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.

    RSL Resuprime Binder (formerly Resutop Binder) is a low viscosity two-pack epoxy resin for application to penetrate deeply into defective concrete flooring as well as sand and cement screeds to consolidate and bind the particles together. The resultant finish is a high strength screed, capable of meeting the stringent industrial demands required for such systems and avoiding the costs and disruptions of screed replacements.



    Features & Benefits


    • Two-pack epoxy resin
    • Results in a high strength screed for industrial use
    • Economic - avoids the costs and disruption of screed replacements
    • Penetrates deeply, consolidating and binding particles together in defective concrete flooring, sand and cement screeds
    • Hygienic and easily cleaned
    • Low odour
    • No shrinkage on curing
    • Excellent hard wearing finish
    • Recommended uses:
      • Food processing and beverage areas
      • Chemical plant rooms
      • Engineering workshops
      • Automotive & aviation areas
      • Factory units
      • Warehouses



    Product Information


    Product Information
    System Thickness (Recommended)200-250 microns WFT 152-190 microns DFT
    *As this product is intended for penetration into porous substrates then the system thickness and coverage rates will depend highly upon the condition of the substrate. The thicknesses given here are intended as a guide only.
    Solids Content by Weight76%
    Solids Content by Volume76%
    Pack Make Up1 x Base 1 x Hardener
    Shelf Life36 months (Base) & 24 months (Hardener) in unopened containers
    StorageKeep out of direct sunlight. Store in a dry place between 15°C - 30°C
    Application Information (at 20°C)
    Coverage Rate (Theoretical)5 Kg. will cover 23.2m² @ 200 microns wet film thickness.
    Coverage rate is calculated based on a sealed and smooth surface and may vary based on the substrate roughness and other conditions.
    Pot LifeApprox. 30 Minutes from mixing, based on 5kg pack size.
    The pot life may be shorter for larger pack sizes if the paint is not used within the pot life limit. Note: All mixed paint must be used within the pot life time limit, if the paint is left in the container after mixing and not used, it may release hazardous fumes due to exothermic reaction.
    Recoating Intervals6 hours or once surface has lost tackiness
    Light Traffic12 - 16 hours
    Full Traffic24 - 36 hours
    Full Chemical Cure7 days
    Technical Information
    Category GuideFerFA Category 3
    Slip Resistance (Method BS7976 pt1-3 2002)Dry > 36
    Wet Please consult Sherwin-Williams/Rawlins Paints Technical
    The slip resistance of a floor surface can vary as a result of the installation process, conditions at the time of application and subsequent traffic. Inappropriate cleaning or maintenance can adversely affect the performance. For further advice on potential wet areas please consult Sherwin-Williams/Rawlins Technical
    Temperature ResistanceTolerant of temperatures up to 45°C
    Chemical ResistanceGood Chemical Resistance - Consult Sherwin-Williams/Rawlins Technical on specific materials
    VOC253 g/l Calculated per full mixed unit
    Life ExpectancyDependant on floor system



    Products required for this system


    • Primer : N/A
    • System : Resutop Binder
    • Surface Seal : As per specification



    Preparation


    New Concrete Floors:

    New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm² is required.

    Existing Concrete Floors:

    Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Resuscreed PA or Resuflor Screed.

    Existing Floors (previously coated)

    All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. if the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.

    Where Resutop Binder is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.



    Application


    The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period , as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C.

    Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation.

    Pre-mix the base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two minutes or until the two components have fully combined.

    The mixed unit should be applied immediately by squeegee, roller or brush with a consistent procedure. Floor areas should be cross-rolled to ensure even application and to minimise roller marks. The product may be poured onto the floor in small pools and immediately rolled evenly over the surface and allowed to penetrate.

    While the product is penetrating into the screed, keep rolling fresh material over the surface until it is visibly obvious that penetration is ceasing and a slight surface residue remains.

    Allow to cure overnight at 20°C then the screed may be recovered with a resin topping, tiles or carpeting etc. and put back into use. Coverage rates will depend on porosity of the substrate. Typically on failed concretes 5 kgs. of Resutop Binder covers around 10m².

    NOTE: Applied coating should be protected from moisture during application and during the curing period. Exposure to moisture during this time can cause surface and colour variations.

     

    Product Details
    4268

    Data sheet

    Manufacturer
    RSL
    For Use By
    Industrial Use
    Parts
    2
    Base Type
    Epoxy
    Minimum Applied Thickness
    200 microns per coat
    Solvent
    -
    Suitable Substrates
    Concrete, cement
    Key Features
    Avoids the costs and disruptions of screed replacements
    Application
    Squeegee, roller, brush
    Dry to Recoat (at 20°C)
    6 hours or once surface has lost tackiness
    Fully Cured (at 20°C)
    7 days
    Pot Life (at 20°C)
    Approx. 30 Minutes from mixing, based on 5kg pack size.
    Coverage
    5 Kg. will cover 23.2m² @ 200 microns wet film thickness.
    Recommended Thinner/Cleaner
    R.S. Industrial Floor Cleaner, R.S. Tyre Mark Remover, R.S. Fats, Oils & Grease Remover & R.S. Oil Remover.
    Unit Contents
    Base & hardener
    Compatible Primers
    -
    Max. Application Temperature
    -
    Min. Application Temperature
    15°C
    Solids by Volume
    76%
    Heat Resistance (up-to)
    45°C
    VOC
    253 g/l Calculated per full mixed unit
    Shelf Life (from date of manufacture)
    36 months (Base) & 24 months (Hardener) in unopened containers
    Resistance to chemicals
    Good Chemical Resistance
    Dry for Light Traffic (at 20°C)
    12 - 16 hours
    Dry for Full Traffic (at 20°C)
    24 - 36 hours
    Suitable For Use On
    Cement
    Suitable For Use On
    Concrete
    Components
    2K
    Colour Family
    Clear
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    RSL Resuprime Binder is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    RSL Resuflor Screed

    Resuflor Screed (formerly known as Resuscreed 45) is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish.Less dust than other screeds Low odour Hard wearing Abrasion and impact resistant Can form coving and falls Can be...

    Price £72.70 (ex. VAT)
    In Stock and Available for Delivery

    RSL Resuflor Patch

    RSL Resuflor Patch (Formerly known as Resuscreed PA and Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments.Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum surface preparation...

    Price £42.48 (ex. VAT)
    In Stock and Available for Delivery