Fosroc Nitoflor FC150 is a is a high performance, solvent free, epoxy resin coating system supplied in pre-weighed packs ready for onsite mixing and use.
Suitable for use on concrete in production assembly areas, workshops, dairies, soft drinks production and bottling plants, breweries, kitchens, showrooms and internal car parks. It is particularly suitable in wet working areas and where chemical spillage is likely, e.g. plating shops, processing plants and dye works.
Nitoflor FC150 is used to provide a hard wearing, easily cleaned, attractive floor coating in industrial areas where high resistance to chemical attack and an abrasion resistant floor finish is required.
Please note: Colours shown are for illustrative purposes only. Special RAL colours available - call0113 2455450or send a message to[email protected].
All coating work to be carried out in accordance with the relevant sections of BS 6150:2006, Painting of Buildings - Code of Practice
New concrete floors: Unless specially water-reduced, the floor should be at least 28 days old and have a moisture content of less than 5%. Where these conditions are not met it may be possible to use Fosroc Nitoflor DPM as a primer
Priming is not normally required provided the concrete substrate is sound, untreated, good quality and non-porous
Nitoflor coatings should not be applied onto surfaces known to or are likely to suffer from rising damp, potential osmosis problems or have a relative humidity greater than 75% as measured in accordance with BS 8203 Appendix A or by a Vaisala thermohygrometer type HMI 31
Fosroc does not recommend acid etching as a method of floor preparation. If used, the method should be approved by the project consultant
In common with all epoxy materials, some slight shade changes may be experienced over the long term when placed in adverse exposure conditions. Any such change in shade is not regarded as being detrimental to performance
The manufacture of Nitoflor FC150 is a batch process and despite close manufacturing tolerances variation may occur between batches. Fosroc recommends using material from one batch only as the finish topcoat
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contactedto obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditionsand should be applied only by an individual with the necessary expertise and experience.We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Fosroc Nitoflor FC150 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Fosroc Cemtop GP is a polymer modified, cement based, floor levelling compound. Suitable for use as a general purpose self-levelling underlayment before the application of floor finishes such as tiles, carpet, vinyl or Fosroc Cemtop XD. Cemtop GP is also suitable as a floor finish for foot traffic or light commercial areas. Please also see...
Fosroc Cemtop XD is a polymer modified, cement based, floor levelling compound. For use as a heavy duty, highly abrasion resistant floor surfacing system. Suitable for industrial and commercial buildings, for new construction or refurbishment projects. Please also see the 'Uses' table in the Product Data Sheet. Fosroc Cemtop GP is also...
Fosroc Nitoprime 33 is the recommended primer for the Fosroc Cemtop range of cementitious self-levelling floor toppings applied to concrete and cementitious substrates. It is a water-based primer which seals the substrate preventing the release of air by the concrete that could form bubbles in the flooring compound. In addition, it “wets” the...
Fosroc Nitoflor Anti-Slip Grains are a range of anti-slip additives which can be added to products including Fosroc Nitoflor FC150 and NitoFlor FC130 and other products in the Fosroc Nitoflor range to provide a slip resistant finish. Available in three grades: 'Fine*', 'Medium' and 'Course'. Please see the Product Data Sheet for the relevant...
Fosroc Nitoflor DPM is a two-component, solvent-free liquid applied surface damp proof membrane and residual moisture suppressant for concrete floors. Suitable for use as an overlay damp roof membrane to cementitious surfaces which were laid without an underlaying damp proof membrane. Nitoflor DPM permits early overlaying with vinyls,...
Fosroc Nitoprime 25 is a two component solvent containing primer consisting of modified epoxy resin. Suitable for use in conjunction with selected Fosroc Nitomortar, Nitoflor and Nitocote products on porous concrete. Please see the Product Data Sheet for the relevant base product for application and mixing details for Nitoprime 25. More...