• RSL Resuscreed 45
  • RSL Resuscreed 45

RSL Resuflor Screed


Resuflor Screed (formerly known as Resuscreed 45) is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish.

  • Less dust than other screeds
  • Low odour
  • Hard wearing
  • Abrasion and impact resistant
  • Can form coving and falls
  • Can be feather edged
  • Can act as a repair system
  • Please note that the 45KG size has a minimum order quantity of 70 units and a 5-day lead time, due to being made to order. If you would like to order this size, contact our sales team on 0113 2455450 or send a message to [email protected]

£72.70(ex. VAT)
£87.24 (inc. VAT)
Please choose your colour
Available for Delivery (See Delivery Options Below)


Resuflor Screed (formerly known as Resuscreed 45) is the perfect screed for heavy duty industrial environments where you are wanting dust kept to a minimum and a highly abrasive floor for heavy traffic. It is also a good choice for food environments due to its hygienic components and has excellent colour stability. It has an strong slip-resistance which means it is suitable for automotive floors.

If you require an impervious finish, we recommend using RSL’s R.S. Screed Seal Clear in conjunction with this product.

Recommended Uses

  • Food and beverage outlets
  • Car showrooms
  • Garage industry
  • Industrial workshops
  • Aerospace production units
  • Engineering environments
  • Chemical storage units
  • Printing and packaging warehouses


New concrete floors: Must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing. Make sure all residue detergent is washed and removed by rinsing with clean water.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability as it may not be compatible with existing floor coating.

Where overcoating other systems such as epoxy coatings or screeds, as part of a specified composite system in the data sheets, please follow the recoat time as stated in the individual data sheets, the coating in each stage should be tack free, but not fully cured. If fully cured, then mechanical preparation is required to ensure intercoat adhesion.


Open and porous substrates may require priming with Resuseal WB, also Resuprime NT may be used as primer on dry substrates only with less than 75% ERH reading. Where the relative humidity of a substrate exceeds 75% ERH, R.S. Dampshield should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table:

ERH % Required Coating Thickness
75-85 1 coat of R.S. Dampshield at 200 microns per coat
85-92 2 coats of R.S. Dampshield at 200 microns per coat
92-97 3 coats of R.S. Dampshield at 200 microns per coat

For further information please refer to recommended individual product data sheets.


The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C to allow the ambient and substrate temperature to stabilise prior to installation.

Mixing: Pre-mix the coloured base component to a uniform consistency (N.B. base will appear gelled in the tin but will become fluid with mixing) then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used, mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Add the aggregate component slowly whilst mixing. Mix using an electric mixer for approximately two to three minutes until the three components have fully combined. For larger units a forced action mixer may be required to fully combine the aggregate into the resins.

Resuflor Screed should be worked with a trowel or float to achieve a dense, compacted finish. This is best achieved by the application of smooth even pressure in one direction, gradually increasing the pressure as the material compacts and beds down. Over-working the material will draw fines to the surface which may result in resin-rich spots and finish variations.

Product Details

Data sheet

For Use By
Industrial Use
Interior / Exterior Use
For Use On
Concrete Floors
Application Method
Single, Two or Three Pack
22.5Kg will cover 2.81 m sq. @ 4mm or 1.87 m sq. @ 6mm
Touch Dry
12-16 Hours
Base Type
Solvent Free Epoxy
Suitable For Use On
Concrete Floors
Application Method
Application Method
Product Type
Floor Screed
Product Range
Colour Family

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Be the first to ask a question about this product!

Question about the product

* Required fields


RSL Resuflor Screed is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT

You might also like

RSL Resuflor WB - Standard Readily Available Colours

Resuflor WB (formerly known as Resuseal WB) is a multi-purpose, two-pack, water-based epoxy coating primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish.  These standard colours are readily available with faster shipping options; more colours are also available...

Price £179.39 (ex. VAT)
In Stock and Available for Delivery