Resuseal WB is a multi-purpose, two-pack, water-based epoxy coating primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish. Low odour Silica Free Superb adhesion Hard wearing Hygienic Dust-free Some product colours are made to order and have minimum...
RSL Resuscreed 55
Resuscreed 55 is a flecked epoxy resin floor screed for concrete, wood metal and other surfaces with sound and clean substrates. It produces a seamless finish to new and existing floors.
- Hard wearing
- Can be a repair system
- Feather edged option
- Low odour
- Can be used to form coving and falls
- Abrasive/Impact resistant
- See ordering references below
- Please note that some products have minimum order quantities; these are made to order and may have extended lead times
|Colour||Nearest RAL Match||Size||Finish||Mimimum Order Quantity|
|Black||RAL 9017||27.5KG or 55KG||Textured||10|
|Flint Grey||RAL 7005||27.5KG or 55KG||Textured||1|
|Salsa Red||RAL 3011||27.5KG or 55KG||Textured||10|
|Stirling Grey||RAL 7004||27.5KG or 55KG||Textured||10|
|White||RAL 9003||27.5KG or 55KG||Textured||10|
|Forest Green||RAL 6002||27.5KG or 55KG||Textured||10|
|Kingfisher Blue||RAL 5017||27.5KG or 55KG||Textured||10|
|Poppy Red||RAL 3020||27.5KG or 55KG||Textured||10|
|Tuscan Green||RAL 6011||27.5KG or 55KG||Textured||10|
Please note that some products have minimum order quantities; these are made to order and may have extended lead times
Resuscreed is more environmentally friendly than other seal coats due to the aggregate being free of crystalline silica. It is designed to produce an impervious finish. For best results, use in conjunction with R.S. Screed Seal by Resin Surfaces Limited (RSL).
- Aerospace areas
- Automotive industry
- Chemical storage areas
- Printing and packaging floors
New concrete Floors: Must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue detergent is washed and removed by rinsing with clean water.
Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability as it may not be compatible with existing floor coating.
Where overcoating other systems such as epoxy coatings or screeds, as part of a specified composite system in the data sheets, please follow the recoat time as stated in the individual data sheets. The coating in each stage should be tack free, but not fully cured. If fully cured, then mechanical preparation is required to ensure intercoat adhesion.
Open and porous substrates may require priming with Resuseal WB, also Resuprime NT may be used as primer on dry substrates only with less than 75% ERH reading. Where the relative humidity of a substrate exceeds 75% ERH, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.
The number of coats to be applied is chosen in accordance with the following table:
ERH % Required Coating Thickness
75-85 1 coat of Resuprime MVT at 200 microns per coat
85-92 2 coats of Resuprime MVT at 200 microns per coat
92-97 3 coats of Resuprime MVT at 200 microns per coat
For further information please refer to recommended individual product data sheets.
The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C to allow the ambient and substrate temperature to stabilise prior to installation.
Mixing: Pre-mix the coloured base component to a uniform consistency (N.B. The base will appear gelled in the tin but will become fluid with mixing), then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used, mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Add the aggregate component slowly whilst mixing. Mix using an electric mixer for approximately two to three minutes until the three components have fully combined. For larger units a forced action mixer may be required to fully combine the aggregate into the resins.
Resuscreed 55 should be worked with a trowel or float to achieve a dense, compacted finish. This is best achieved by the application of smooth even pressure in one direction, gradually increasing the pressure as the material compacts and beds down. Over-working the material will draw fines to the surface which may result in resin-rich spots and finish variations.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Trowel, Float.
- 27.5Kg will cover 2.75 m sq. @ 5mm or 1.37 m sq. @ 10mm
- Touch Dry
- 12-16 Hours
Be the first to ask a question about this product!
RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood. Features and Benefits:...