RSL R.S. Terrazzo Marble
  • RSL R.S. Terrazzo Marble
  • RSL R.S. Terrazzo Marble
  • RSL R.S. Terrazzo Marble
  • RSL R.S. Terrazzo Marble
  • RSL R.S. Terrazzo Marble
  • RSL R.S. Terrazzo Marble

RSL R.S. Terrazzo

EPTMB

R.S. Terrazzo is a 4-part decorative seamless floor finish comprised of inert marble aggregates and epoxy resin. It provides both a high wear and decorative finish for public areas such as shopping centres, airports and supermarkets.

  • Chemical resistant
  • Anti-slip
  • Extremely hard wearing
  • Hot water resistant
  • Decorative

**Available for delivery - see Delivery Options below**

Colour
  • Current colour: White
Choose a colour
Close colour picker
  • White
  • Black
  • Salsa Red
  • Stirling Grey
  • Flint Grey
  • Savannah Yellow
  • Marigold
Size
£120.81
VAT excluded

£144.97 Tax incl.
Quantity

Description

R.S. Terrazzo is a heavy duty decorative epoxy terrazzo effect seamless floor finish produced from inert marble aggregates and epoxy resin. R.S. Terrazzo is ideal where there is both a high wear and aesthetic decorative requirement such as shopping centres, retail outlets, airport terminals and office buildings.

It was installed in Hope Hospital by Balfour Beatty, a commission from Salford Royal NHS Foundation Trust. It was during this project that the marble aggregates were combined with granite aggregates to fit their requirements.

R.S. Terrazzo was also used to refurbish the floor, stairs and ramped areas of Manchester Central Library, keeping in fitting with the Grade II Listed building’s decor.



Features & Benefits


  • Decorative
  • High chemical resistance
  • Resistant to hot water and steam
  • Excellent slip resistant finish
  • Extremely hard wearing
  • Recommended uses:
    • Building entrances
    • Food manufacture and processing
    • Retail outlets
    • Corridors
    • Pharmaceutical & chemical plant processing
    • Abattoirs
    • Heavy duty plant and traffic areas



Product Information


Product Information
System Thickness (Recommended) 8-10mm
Solids Content by Weight 100%
Pack Make Up 1 x Base 1 x Hardener 1 x Powder Aggregate 1 x Aggregate
Shelf Life 12 months (Base, Hardener & Aggregates)
Storage Keep out of direct sunlight. Store in a dry place, between 15°C- 30°C
Application Information (at 20°C)
Coverage Rate (Theoretical) 30Kg will cover 1.5 m 2 @ 10mm ground back to 8mm
Pot Life 30 Minutes
First Grind 48-72 hours
Wet Polish 16-24 hours after grouting
Final Seal Coats 16-24 hours after wet polishing
Full Chemical Cure 7 days
Technical Information
Category Guide FerFA Category 8
Slip Resistance Dry >60
Method BS7976 pt1-3 2002 Wet - Please consult Sherwin-Williams/Rawlins Paints Technical
The slip resistance of a floor surface can vary as a result of the installation process, conditions at the time of application and subsequent traffic. Inappropriate cleaning or maintenance can adversely affect the performance. For further advice on potential wet areas please consult Sherwin-Williams/Rawlins Technical
Abrasion Resistance (Method BS8204 /ASTM D4060) n/a
Temperature Resistance Tolerant of temperatures up to 120°C at 9mm
Chemical Resistance Good chemical resistance - Consult Sherwin-Williams/Rawlins Technical
VOC < 9 g/l Calculation based on a full mixed unit
Life Expectancy Up to 10 years - subject to industrial traffic. Sherwin-Williams terms and conditions will apply



Products required for this system




Preparation


New Concrete Floors:

Must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue detergent is washed and removed by rinsing with clean water.

Existing Floors (previously coated)

All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability as it may not be compatible with existing floor coating.

Where overcoating other systems such as epoxy coatings or screeds, as part of a specified composite system in the data sheets, please follow the recoat time as stated in the individual data sheets, the coating in each stage should be tack free, but not fully cured. If fully cured then mechanical preparation is required to ensure intercoat adhesion.



Priming


Open and porous substrates may require priming with Resuseal WB, also Resuprime ST may be used as primer on dry substrates only with less than 75% ERH reading. Where the Relative Humidity of a substrate exceeds 75% ERH Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table:

ERH% Required Coating Thickness
75-85 1 coat of Resuprime MVT at 200 microns per coat
85-92 2 coats of Resuprime MVT at 200 microns per coat
92-97 3 coats of Resuprime MVT at 200 microns per coat



Application


The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilize prior to installation.

Mixing:

Pre-mix the coloured base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Transfer to a forced action mixer and add the aggregate components slowly whilst mixing. Add the powder first followed by the marble aggregate. Mix for approximately two to three minutes until the three components have fully combined.

R.S Terrazzo should be worked with a trowel or float to achieve a dense, compacted finish. Apply at nominal 10mm between battens to the primed concrete with a steel float to produce a uniform level finish. This is best achieved by the application of smooth even pressure in one direction, gradually increasing the pressure as the material compacts and beds down.

After curing for a minimum of 48 hours at 20°C, grinding can commence on R.S. Terrazzo. This is followed by a fine cut to remove cutting marks. Care must be taken to use appropriate equipment to achieve the necessary finish.

 

Product Details
EPTMB

Data sheet

Manufacturer
RSL
Parts
4
Base Type
Water-based polyurethane resin
Interior/Exterior Use
Interior
Minimum Applied Thickness
10mm, ground back to 8mm
Suitable Substrates
Concrete
Key Features
Decorative terrazzo effect, hardwearing and chemical resistant
Application
Trowel, Float
Dry to Recoat (at 20°C)
-
Fully Cured (at 20°C)
7 days
Coverage
30Kg will cover 1.5 m 2 @ 10mm ground back to 8mm
Recommended Thinner/Cleaner
R.S. Industrial Floor Cleaner, R.S. Tyre Mark Remover, R.S. Fats, Oils & Grease Remover & R.S. Oil Remover.
Compatible Primers
Resuseal WB, Resuprime ST, Resuprime MVT
Max. Application Temperature
-
Min. Application Temperature
15°C
Density
1.04 (relative)
Solids by Volume
-
Dry for Light Traffic (at 20°C)
-
Dry for Full Traffic (at 20°C)
-
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send