707 MMA Metal Primer
  • 707 MMA Metal Primer

707 MMA Metal Primer

RAW707

707 MMA Metal Primer is a rapid curing three-pack primer for steel, galvanised steel, aluminium, and unglazed ceramic tiles to be used prior to any of the MMA range of coatings, mortars, and screeds.

  • Rapid cure, even at low temperatures - from as low as -30°C*
  • Very good corrosion resistance
  • Excellent adhesion
  • Impervious to water
  • Pre-packed units ready for use
  • Easily applied
  • Can be overcoated after 40 minutes @ 20°C
  • 5kg pack is sufficient to prime an area of 15-20m²
  • Click to jump down to Technical Data

*Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]

Colour
Size
£85.05
VAT excluded

£102.06 Tax incl.
Quantity

Description

707 MMA Metal Primer has been developed as a primer for steel, galvanised steel, aluminium, and unglazed ceramic tiles to be used prior to any of the MMA range of coatings, mortars, and screeds.

The product exhibits outstanding adhesion to steel surfaces, and the fast curing characteristics allow rapid application of subsequent coatings, mortars or screeds

707 MMA Metal Primer is supplied as a three pack material, comprising pre-weighed amounts of Base, Catalyst and Adhesion promoter components.



Quick Links - Click To Jump To Section:




Features & Benefits


  • For steel, galvanised steel, aluminium, and unglazed ceramic tiles
  • To be used prior to any of the MMA range of coatings, mortars, and screeds
  • Rapid cure, even at low temperatures - from as low as -30°C*
  • Very good corrosion resistance
  • Excellent adhesion
  • Impervious to water
  • Pre-packed units ready for use
  • Can be overcoated after 40 minutes @ 20°C
  • 5kg pack is sufficient to prime an area of 15-20m²
  • Easily applied
  • Three pack

*Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]



Typical Properties


Technical Data
  707 MMA Metal Primer
Viscosity: 300 cps @ 20°C
Pot life @ 20°C: 15 Minutes
Pot life @ 10°C: 25 minutes
Adhesion to concrete: 15MPa
Temp. range during application: -30°C* to + 40°C
Temp. range during service: -40°C to + 60°C



*Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]





Coverage


  • A 5kg pack is sufficient to prime an area of 15-20m²
  • Exceptionally porous surfaces may require a second coat



Surface Preparation


Steel/Galvanised Steel:

  • Any rust, mill scale and other contaminants should be removed by gritblasting to Swedish Standards Sa 2.5
  • Reduced levels of surface preparation, e.g. wire brushing to remove loose rust, are permissible, but will lead to lower performance characteristics

Ceramic Tiles:

  • Abrade to roughen the surface, removing any dust



Mixing:

  • Pour the contents of the Adhesion Promoter container into the Base container and thoroughly mix, preferably by mechanical means
  • Then add the Catalyst component and mix to a uniform consistency



Mixing Ratio:

  • (% Catalyst by Weight) = 3.4



Application


  • Apply by squeegee, brush or roller at a nominal application rate of 0.25-0.30kg/m²
  • Allow to cure for a minimum of 40 minutes prior to applying any other MMA products from our range
  • If an interval of more than 8 hours between primer application and subsequent overcoating is anticipated, or when priming ceramic tiles, then the primer shall be scattered with 504 Standard Anti-Slip Aggregate before hardening



Cleaning




Curing


  • Minimum overcoating interval: 40 minutes @ 20°C



Limitations


  • Do not apply to wet surfaces

707 MMA Metal Primer will taint food during application, so that all foodstuffs in the immediate vicinity must be removed or properly covered.



Storage & Shelf Life


  • Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 20°C
  • Adequate ventilation of the storage area should be provided
  • Keep container tightly closed when not in use
  • 707 MMA Metal Primer has a minimum shelf life of 12 months when stored in original, unopened containers in accordance with manufacturer’s instructions



Health & Safety


707 MMA Metal Primer is flammable during application, so adequate safety precautions should be observed.

  • Avoid contact of the material with skin and eyes
  • Wear gloves and goggles
  • Wash off splashes immediately with soap and water
  • Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought
  • Please refer to Material Safety Data Sheet for additional information
  • 707 MMA Metal Primer shall be applied strictly in accordance with the manufacturer’s instructions

For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]



It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
RAW707

Data sheet

For Use On
Metal, Steel, Galvanised Steel, Aluminium, Unglazed Ceramic Tiles
Application Method
Squeegee, Brush, Roller
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Three-Pack
Pot Life (at 20°C)
15 minutes
Coverage
A 5kg pack is sufficient to prime an area of 15-20m²
Max. Application Temperature
40°C
Min. Application Temperature
-30°C
Shelf Life (from date of manufacture)
12 Months
Touch Dry
40 mins
UN Number
UN2924
UN Number (Activator)
UN3106
UN Number (Base)
UN1866
Viscosity
300 cps @ 20°C
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

504 Standard Anti Slip Aggregate

504 Standard Anti Slip Aggregate is a specially formulated quartz aggregate to be added to various products in our floor coatings range to provide increased 'anti-slip' properties in both dry and wet conditions to improve safety. Produces a rough, non-skid surface Hard wearing and chemical resistant Coloured Quartz Aggregate 0.4-0.8mm...

Price £8.51
In stock

109 Tool Cleaner

109 Tool Cleaner is a specialist equipment cleaner suitable for the removal of uncured epoxy, polyester and polyurethane resins. Low Hazard Low evaporation rate Excellent solvency powers 80% biodegradable Click to jump down to Technical Data

Price £30.62
In stock