709 MMA Damp Proof Primer has been developed as a primer for damp concrete, being used prior to any of our MMA range of coatings, mortars, and screeds.
Rapid cure, even at low temperatures - from as low as -30°C*
Very good chemical resistance
Excellent adhesion to damp concrete
Impervious to water
Pre-packed units ready for use
Easily applied
Can be overcoated after 30 minutes @ 20°C
Suitable for 7 day old concrete
Images are for illustrative purposes only and may differ from the actual product
709 MMA Damp Proof Primer has been developed as a primer for damp concrete, being used prior to any of our MMA range of coatings, mortars, and screeds.
The product exhibits outstanding adhesion to damp concrete, and the fast curing characteristics allow rapid application of subsequent coatings, mortars or screeds.
709 MMA Damp Proof Primer is supplied as a three pack material, comprising pre-weighed amounts of Base, Catalyst and Filler components.
A 5kg pack is sufficient to prime an area of 6-12m²
Surface Preparation
Concrete surfaces shall be a minimum of 7 days old
Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound, and existing paint finishes, etc
Suitable mechanical treatment such as vacuum grit blasting or mechanical scabbling is recommended to ensure the removal of contaminants and to provide a mechanical ‘key’ for the primer
Ensure that no standing water is present on the surface
Mixing:
Pour the contents of the Catalyst container into the Base container, add the Filler component, and thoroughly mix, preferably by mechanical means
Mixing Ratio:
(% Catalyst by Weight) = 2
Application
Apply by squeegee to distribute evenly over the floor, and then use a long nap lambswool roller to achieve a nominal application rate of 0.4-0.8kg/m², depending on substrate absorbency
Allow to cure for a minimum of 30 minutes prior to applying any other MMA products from the range
For temperatures below 5°C please contact our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for advice
Do not apply to concrete surfaces which have standing water present, or are less than 7 days old
The product does not replace the need for a separate damp proof membrane
709 MMA Damp Proof Primer will taint food during application, so that all foodstuffs in the immediate vicinity must be removed or properly covered
Storage & Shelf Life
Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 20°C
Adequate ventilation of the storage area should be provided
Keep container tightly closed when not in use
709 MMA Damp Proof Primer has a minimum shelf life of 6 months when stored in original, unopened containers in accordance with manufacturer’s instructions
Health & Safety
709 MMA Damp Proof Primer is flammable during application, so adequate safety precautions should be observed.
Avoid contact of the material with skin and eyes
Wear gloves and goggles
Wash off splashes immediately with soap and water
Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought
709 MMA Damp Proof Primer shall be applied strictly in accordance with the manufacturer’s instructions
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
109 Tool Cleaner is a specialist equipment cleaner suitable for the removal of uncured epoxy, polyester and polyurethane resins.
Low Hazard
Low evaporation rate
Excellent solvency powers
80% biodegradable
This product is for Professional Use Only
Images are for illustrative purposes only and may differ from the actual product
Click to...
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
Colourmatch Service Disclaimer
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.