Rust-Oleum 3366 Epoxy Powerfloat Floor Primer Rapid
  • Rust-Oleum 3366 Epoxy Powerfloat Floor Primer Rapid

Rust-Oleum 3366 Epoxy Powerfloat Floor Primer Rapid

3366.5

Rust-Oleum Powerfloat Epoxy Floor Primer Rapid 3366 is a rapid curing 2-component solvent-free epoxy primer designed to improve the adhesion of coatings to difficult substrates such as power-floated concrete.

  • Overcoatable after just 3 hours: apply primer and topcoat in one day
  • Easy all-in-1 packaging
  • For new and aged power floated concrete, even with pinholes
  • Light grey colour to increase opacity of the next layers
  • Water-based; low odour

Colour
Size
Finish
£106.34
VAT excluded

£127.60 Tax incl.
Quantity

Description

Rust-Oleum Powerfloat Epoxy Floor Primer Rapid 3366 is a rapid curing 2-component solvent-free epoxy primer designed to improve the adhesion of coatings to difficult substrates such as power-floated concrete.

Main Properties

Excellent adhesion and binding power - recoating time of only 3 hours allows application of primer and topcoat in one day - product has a light grey finish, creating a better opacity for the following coating.

Recommended Uses

For use on dense, smooth floors like power-floated concrete, quarry tiles and ceramic tiles. Product can be used in combination with all Rust-Oleum or Mathys epoxy and polyurethane coatings. For any other coating, we recommend a test for suitability.

Technical Data

  • Density: 1,1
  • Gloss Level: Satin
  • Solids content in volume: 50 %
  • Solids Content in weight: 65 %
  • Mixing Ratio: Base : Activator = 3 : 2 (Volume) = 1.1 : 1 (Weight)

Drying Times At 20°C/RH 50%

  • Touch dry: 1,5 hours
  • Dry to handle: 2,5 hours
  • Dry to recoat: 3 hours
  • Fully cured: 5 days
  • Pot Life: 2 hours

Theoretical Consumption

10 m²/l

Practical Consumption

Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.

Surface Preparation

New concrete should be allowed at least 30 days to dry. Surfaces should be clean, dry and free from oil, grease, dust, dirt, curing compounds and other contaminants. Remove grease, oil and all other surface contaminations by alkaline or high pressure (steam) cleaning. Remove all previous coatings completely.

Remarks

Although the product will improve adhesion on difficult surfaces the characteristics of such surfaces can vary. For this reason a trial area should be applied to ensure that adequate adhesion can be achieved. This also applies to surfaces which are difficult to clean, such as tiles in bare foot areas. Rust-Oleum 3366 is intended as a primer only, not a wearing surface. The product can never assure good adhesion to unsound, friable, unclean or otherwise unsuitable surfaces. Depending on the substrate and how effectively it can be cleaned, Rust-Oleum 3366 may not be as effective as traditional means of preparation such as shot blasting. We would recommend such methods be used whenever possible, especially for larger or more heavily trafficked areas.

Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
3366.5

Data sheet

Manufacturer
Rust-Oleum
Interior / Exterior Use
Interior
Water / Solvent Based
Water
For Use On
Concrete, Ceramic Tiles
Application Method
Brush, Roller
Sheen
Satin
Colour
Standard / Ready Mixed
VOC Levels
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Two-Pack
Pack Size
5L
Application
Brush, Roller
Dry to Handle (at 20°C)
2 Hours 30 Mins
Dry to Recoat (at 20°C)
3 Hours
Fully Cured (at 20°C)
5 Days
Coverage
10m² per litre
Recommended Thinner/Cleaner
Rust-Oleum Thinner 160.
Density
1,1
Solids by Volume
50 %
VOC
30 g/l
Shelf Life (from date of manufacture)
2 year from date of production in unopened cans, if stored in dry, well ventilated areas, not in direct sunlight at temperatures between 10° and 25°C.
Touch Dry
1 Hour 30 Mins
Recommended Dry Film Thickness
50 µm
Recommended Wet Film Thickness
100 µm
UN Number (Activator)
Not regulated
UN Number (Base)
Not regulated
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Rust-Oleum Thinner 160

Rust-Oleum Thinner 160 is a specially formulated blend of solvents designed to mix with Rust-Oleum`s 1085 Galva Zinc, 9100 High Performance Epoxy and B95 Flexible Epoxy to create an optimal consistency for application whether it be for Brush, Roller or Spray. Can also be used for the cleaning of some surfaces or equipment. Strong dilution...

Price £14.25
In stock