RSL Resuprime OT

PROTB
RSL2937

RSL Resuprime OT (formerly known as R.S. Oil Tolerant Primer) is a two-component epoxy resin floor membrane that combats any residual oil that has escaped into a concrete floor. It ensures that no oil will affect a top finish. 

  • Easy application
  • Application onto substrates with engineering oil contamination
  • Excellent adhesion
  • Low odour
  • High solids

Colour
Size
Finish
£335.49(ex. VAT)
£402.59 (inc. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

Description

RSL Resuprime OT (formerly known as R.S. Oil Tolerant Primer) allows finishes to be applied seamlessly onto concrete that have previously fallen foul of engineering oils.

It can be used on substrates with hygrometer readings of up to 85% RH, and your floor or screed should be at least 50mm thick if unbonded. It must have the required mechanical strength to produce an even coating.

It is essential that all surface and gross contamination is removed by cleaning with R.S. Oil Remover and R.S. Industrial Floor Cleaner. 

Recommended Uses

  • Concretes with oil contamination
  • Where a DPM is ineffective
  • Polymer screeds
  • Cementitious underlayments
  • Factory floors
  • Automotive workshops
  • As a seal coat for contaminated concrete

Preparation

New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm sq. is required.

Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out with Resuscreed PA.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.

RSL Resuprime OT can also be applied to existing coatings and to other cementitious screeds which should be clean and sound with an appropriate mechanical key for adhesion.

Priming

RSL Resuprime OT is suitable on concrete with Relative Humidity readings up to 85% ERH. Where the relative humidity of a substrate exceeds 85% ERH, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table:

ERH% Required Coating Thickness
85-92 2coats of Resuprime MVT at 200 microns per coat
92-97 3coats of Resuprime MVT at 200 microns per coat

For Further information please refer to recommended individual product data sheets.

Application

The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation.

Mixing: Pre-mix the base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used for mixing ensuring all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two to three minutes until the two components have fully combined.

The mixed unit should be applied immediately by squeegee, roller or brush with a consistent procedure. Floor areas should be cross-rolled to ensure even application and to minimise roller marks.

 

Product Details
PROTB

Data sheet

For Use By
Industrial Use
Application
Roller, Brush, Squeegee.
Coverage
5 kg will cover 23 m² @ 200 µm
Touch Dry
8 Hours
Base Type
Solvent-Based
Exterior / Interior Use
Interior Use
Suitable For Use On
Screeds
Suitable For Use On
Concrete
Components
2K
Product Type
Epoxy
Colour Family
Clear
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

RSL Resuprime MVT

RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood.  Easy application Use on...

Price £147.10 (ex. VAT)
In Stock and Available for Delivery

RSL Resuflor Patch

RSL Resuflor Patch (Formerly known as Resuscreed PA and Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments. Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum surface preparation...

Price £42.48 (ex. VAT)
In Stock and Available for Delivery