Resuflor WB (formerly known as Resuseal WB) is a multi-purpose, two-pack, water-based epoxy coating primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish. These standard colours are readily available with faster shipping options; more colours are also available...
RSL Resuprime ESD
RSL Resuprime ESD (formerly known as Resustat CP and Resustat Primer) is designed to be applied prior to the use of Resuflor SL ESD, Resustat SL23, Resustat TG69 or Resustat Terrazzo. It is a low viscosity epoxy primer with conductive fillers.
- Conductive with very low electrical resistance
- Good adhesion
- Low odour
- High solids
- Easy to apply
- Please note this product is made to order, with a lead time of 14-21 days
RSL Resuprime ESD (formerly known as Resustat CP and Resustat Primer) can be applied to wood, concrete, metal and synthetic floors. It is for application before static-dissipative resin flooring systems, which are ideal for industrial and domestic environments with high levels of electrical current.
Resuprime ESD has a conductivity level of less than 0.050 M Ohms when tested in compliance with BS EN 61340.
- Food halls
- Operating theatres
- TV studios
- Prior to applying any of the Resustat range
New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding. A minimum strength of 25N/mm sq. is required.
Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out with Resuscreed PA.
Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.
Resuprime ESD can also be applied to existing coatings and to other cementitious screeds which should be clean and sound with an appropriate mechanical key for adhesion.
Resuprime ESD should be used as a conductive primer only and is normally applied on top of an already primed and sealed surface. The copper tape grid for the earthing should be applied prior to the application of the Resuprime ESD.
Where the relative humidity of a substrate exceeds 75% ERH, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.
The number of coats to be applied is chosen in accordance with the following table:
The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally, to allow the ambient and substrate temperature to stabilise prior to installation.
Mixing: Pre-mix the base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used for mixing, ensure all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two to three minutes until the two components have fully combined.
The mixed unit should be applied immediately by roller or brush with a consistent procedure. Floor areas should be cross-rolled to ensure even application and to minimise roller marks.
- For Use On
- Application Method
- Brush, Roller, Squeegee
- Textured Gloss
- Standard / Ready Mixed
- VOC Levels
- Low (50-149 g/l)
- Single, Two or Three Pack
- Pack Size
- Brush, Roller
- 5kg will cover 21.7m sq. @ 200 microns WFT.
- Touch Dry
- 8 Hours.
- UN Number (Activator)
- UN Number (Base)
Be the first to ask a question about this product!
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. Resuprime ST (formerly known as Resuprime) is a two-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and...
RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood. Easy application Use on...
RSL Resuflor Patch (Formerly known as Resuscreed PA and Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments. Features and Benefits: Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum...