RSL Resuprime ST Bonding & Priming Coat


Resuprime ST (formerly known as Resuprime) is a two-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces. 

Features and Benefits:

  • Versatile for many types of application
  • Excellent adhesive properties
  • Easy to apply
  • Can be used as a tack coat for screeds
  • No unpleasant or harmful odours
£108.46(ex. VAT)
£130.15 (inc. VAT)
Please choose your colour
Available for Delivery (See Delivery Options Below)


Resuprime ST (formerly known as Resuprime) provides excellent adhesion both as a tack coat and primer. Where surfaces are very porous, a coat of Resuprime ST may be required as a pre-primer coat before a second coat is applied as a tack coat.

For application onto new concrete, or where the RH level is likely to be above 75%, Resuprime MVT (formerly known as R.S. Dampshield FH) should be applied.

Resuprime ST is also suitable for priming self-smoothing epoxy resin finishes such as Resuflor and resin based concrete repair products such as Resupatch. Resuprime ST can also be used as a primer for high build epoxy resin coatings such as Resutop and Resucoat H.B.

Recommended Uses

  • Concrete primer and sealer
  • As a primer for Sherwin-Williams floor coatings and screeds – this includes RSL products.


New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding. A minimum strength of 25N/mm sq. is required.

Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water.

Local repairs should be carried out with Resuflor Patch or Resuflor Screed.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with the existing floor coating.

Resuprime ST can also be applied to existing coatings and to other cementitious screeds, which should be clean and sound with an appropriate mechanical key for adhesion.


Resuprime ST is suitable for application onto concrete and other substrates where the relative humidity is less than 75% ERH. Hygrometer readings should be done in accordance with BS 8203 to confirm the ERH of the substrate prior to application.

If the ERH is above 75%, then Resuprime MVT (formerly known as R.S. Dampshield FH) should be used in place of Resuprime ST.


The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally, to allow the ambient and substrate temperature to stabilise prior to installation.

Mixing: Pre-mix the base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used for mixing, ensure all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two to three minutes until the two components have fully combined.

The mixed unit should be applied immediately by squeegee, roller or brush with a consistent procedure. Floor areas should be cross-rolled to ensure even application and to minimise roller marks. Coverage rates may vary depending on profile and porosity of the substrate.

Product Details

Data sheet

For Use On
Application Method
Brush, Roller, Squeegee
Smooth Gloss
VOC Levels
Low (50-149 g/l)
Single, Two or Three Pack
Pack Size
Brush, Roller, Squeegee
5kg will cover 23m sq. @ 200 microns WFT
Touch Dry
8 Hours
UN Number (Activator)
UN Number (Base)

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Be the first to ask a question about this product!

Question about the product

* Required fields
You might also like

RSL Resuflor Screed

Resuflor Screed (formerly known as Resuscreed 45) is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish. Less dust than other screeds Low odour Hard wearing Abrasion and impact resistant Can form coving and falls Can be...

Price £69.24 (ex. VAT)
In Stock and Available for Delivery

RSL Resuprime MVT

RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood.  Easy application Use on...

Price £140.10 (ex. VAT)
In Stock and Available for Delivery

RSL Resuflor Patch

RSL Resuflor Patch (Formerly known as Resuscreed PA and Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments. Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum surface preparation...

Price £40.46 (ex. VAT)
In Stock and Available for Delivery