We no longer stock this product, but can recommend RSL Resuprime MVT as a great alternative.
Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.
Resuprime MVT LT (formerly known as Resuprime PP) is a 2-part fast curing, moisture tolerant two-component epoxy primer/membrane for application on cold and damp concrete floors. This enables earlier access onto new concrete substrates for the application of screeds, coatings and other floor coverings including carpets, tiles, vinyl and wood.
Resuprime MVT LT is also used for existing concrete slabs where there is no damp proof membrane or where a degree of moisture tolerance is required for a resin floor system being installed.
Features & Benefits
Formerly known as Resuprime PP
Fast curing, moisture tolerant two-component epoxy primer/membrane
2-part
Applies to cold and damp concrete floors
Enables earlier access onto new concrete substrates for the application of screeds, coatings and other floor coverings including carpets, tiles, vinyl and wood
Also for existing concrete slabs where there is no damp proof membrane
Ease of application
Damp and moisture tolerant
Fast cure even at low temperatures down to 5°C
Low odour
Excellent adhesion
Solvent free
Recommended uses:
“Green” concrete
Concrete substrates with no DPM
Fast return to service at normal temperatures
Polymer screeds
Cementitious underlayments
Low temperature applications
Product Information
Product Information
Volume Solids
~100%
VOC
<15 g/l calculated per full mixed unit
Finish
Smooth gloss
Flash Point
N/A
Cleanser/Thinner
N/A
Pack Weights
2.99 kg base/2.01 kg hardener (5 kg)
8.97 kg base/6.03 kg hardener (15 kg)
Mixing Ratio
3 parts base to 2 part hardener by weight only
Mixed Density
Approximately 1.08 g/cm³
Shelf Life
36 months (Base), 12 months (Hardener)
Storage
Keep out of direct sunlight. Store in a dry place between 15°C - 30°C
Recommended Application Methods
Brush, roller or squeegee
Application Information (at 20°C)
Recoating Intervals
4-5 hours or once surface has lost tackiness
Light Traffic
18 – 24 hours
Full Traffic
36 – 48 hours
Full Chemical Cure
7 days
Pot Life
15 – 20 minutes from mixing, based on 5 kg pack size
The pot life may be shorter for larger pack sizes if the paint is not used within the pot life limit. Note: All mixed paint must be used within the pot life time limit, if the paint is left in the container after mixing and not used, it may release hazardous fumes due to exothermic reaction.
Coverage Rate (Theoretical)
5 kg will cover 25 m² @ 200 µm WFT
Coverage rate is calculated based on a sealed and smooth surface and may vary based on the substrate roughness and other conditions.
System Thickness (recommended)
200 – 250 µm
Technical Information
Category Guide
FerFA Category 2
Bond strength
>3 N/mm² (Substrate failure)
Temperature Resistance
Tolerant of temperatures up to 60°C
Preparation
New Concrete Floors:
New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm² is required.
Existing Concrete Floors:
Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and making sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Resuflor Patch.
Existing Floors ( previously coated )
All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with the existing floor coating.
Where Resuflor Patch is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.
Recommended Systems
Where the Relative Humidity of a substrate exceeds 85% ERH Resuprime MVT LT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203:2017.
The number of coats to be applied is chosen in accordance with the following table.
ERH%
Required Coating Thickness
75-85
1 coat of Resuprime MVT LT at 200 microns per coat
85-92
2 coats of Resuprime MVT LT at 200 microns per coat
92-97
3 coats of Resuprime MVT LT at 200 microns per coat
Application
The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to the installation.
Product Details
4266
Data sheet
Manufacturer
RSL
For Use On
Concrete
Application Method
Brush, Roller, Squeegee
Sheen
Smooth Gloss
Colour
Clear
VOC Levels
Low (50-149 g/l)
Single, Two or Three Pack
Two-Pack
Pack Size
5KG, 15KG
Parts
2
Base Type
Epoxy
Minimum Applied Thickness
200 microns per coat
Suitable Substrates
Concrete
Key Features
Fast cure even at low temperatures down to 5°C; enables earlier access onto new concrete substrates for the application of screeds, coatings and other floor coverings
Application
Brush, roller or squeegee
Fully Cured (at 20°C)
7 days
Pot Life (at 20°C)
15 – 20 minutes from mixing, based on 5 kg pack size
RSL Resuprime MVT LT is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
RSL Resuflor Patch (Formerly known as Resuscreed PA and Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments.Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum surface preparation...