Rust-Oleum 3333 Super Adhesion Primer provides excellent adhesion on non-porous, dense mineral substrates like:
Rust-Oleum 3333 Super Adhesion Primer provides excellent adhesion on non-porous, dense mineral substrates like tiles or power floated concrete as well as non-ferrous metals like stainless steel, aluminium or new hot-dip galvanized steel and thermosetting plastics like fibreglass-reinforced polyester or epoxy.
Rust-Oleum 3333 Super Adhesive Primer Resists light to moderate abrasion, intermittent high humidity and moisture, regular chemical cleaning and spillage of chemicals if recoated with the appropriate Rust-Oleum system. 3333 Super Adhesive Primer can be recoated with nearly all Rust-Oleum Epoxy, Polyurethane, Chlorinated Rubber/Vinyl and Acrylic coatings. It is also classified Class 1 Surface Spread of Flame according BS 476; part 7: 1987.
NEW: Now also available in convenient 1 litre packaging, ideal for smaller projects the new convenient 2-component packaging provides the base and activator in one convenient kit and the activator is supplied with a user-friendly spout cap.
Features & Benefits
TECHNICAL DATA
| Density: | 1.58 kg/l |
| Gloss Level: | Satin |
| Solids Content in Volume: | 61.9% |
| Heat Resistance: | 150°C (dry heat) |
| Mixing Ratio: | Base : Activator = 0.72 : 0.28 (Volume) |
DRYING TIMES AT 20°C/RH 50%
| Touch Dry: | 6 Hours |
| Dry to Handle: | 8 Hours |
| Dry to Recoat: | 16 h (20°C), 24 h (10°C), 12 h (30°C) |
| Fully Cured: | 8 Days |
| Pot Life: | 2 Hours |
SURFACE PREPARATION
Remove grease, oil and all other surface contaminations with Rust-Oleum FK111 Cleaning Solution or by alkaline or high pressure (steam) cleaning. New concrete should cure and dry for at least 30 days prior to the application of the coatings. The surface must be clean and may be slightly damp during application.
DIRECTIONS FOR USE
Stir individual components thoroughly before mixing them together. Use the boxing method or a low speed mixer.
APPLICATION CONDITIONS
Temperature of air and substrate between 10 and 35°C and relative humidity below 70%. The substrate temperature must be at least 5°C above dew point.
APPLICATION & THINNING: BRUSH
5 up to 10 vol. % with water. Use brushes based on a mixture of synthetic/natural bristles. Check wet film thickness, avoid excessive film thickness. Preferably use disposable brushes.
APPLICATION & THINNING: ROLLER
10 up to 20 vol. % with water. Use short nap (4-6mm) mohair or velvet brush rollers. Check wet film thickness, avoid excessive film thickness. Preferably use disposable rollers.
APPLICATION & THINNING: AIR-ATOMISED SPRAY
Up to 20 vol. % with water. Spray: Gravity cup and pressure cup. Tip size: 1.2 -2.0 mm. Atomizing pressure: 2 - 4 bar. Check wet film thickness, avoid excessive film thickness.
CLEANING OF EQUIPMENT / SPILLS
Immediately after application with (hot) water and soap.
REMARKS
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
 Barbara on 2022-12-02 07:23:22 | Question: Is this product suitable as a primer for old concrete floors, as the spec says for dense, power-floated concrete? I think the floor I want to paint could be a bit porous, and is a bit pitted in places. I want to paint it with Rust-oleum 7200. Water gets splashed on it and it’s walked over a lot. |
Answer from Rawlins’ Technical Team: No this primer is not suitable for application to a porous floor or compatible with Rust-Oleum 7200 Floorcoat PU. Assuming the concrete floor is bare, clean, dry, sound and prepared as detailed in the technical data sheet Rust-Oleum 7200 Floorcoat PU can be applied directly. The first coat should be thinned 5% with Rust-Oleum Thinner 633. | |
| Shah on 2022-02-27 17:59:03 | Question: Could pls tell me the primer is applicable for stainless steel pipe for painting? |
Answer from Rawlins’ Technical Team: Yes this can be applied to non-ferrous metals like stainless steel, aluminium or hot-dip galvaninsed steel, assuming it is clean, dry, sound and prepared as detailed in the technical data sheet. | |
| Bill King on 2021-04-27 06:05:54 | Question: Hi, do you have a Matt black or can you add a colour dye to this.Thanks Bill. |
Answer from Rawlins’ Technical Team: I'm afraid we wouldn't recommend introducing any form of dye or colourant to this product, it is available in clear only. It cannot be left as a finish though so a topcoat must be used. | |
| Dave on 2019-05-02 07:47:24 | Question: Hi could you advise me if this product is suitable for priming porcelain floor tiles?and if so what you recommend as a top coat/sealer? |
Answer from Rawlins’ Technical Team: Yes, clean thoroughly and lightly abrade before application. We would suggest finishing with Rust-Oleum 9200 Rust-O-Thane. | |
| amanda on 2019-04-23 13:23:34 | Question: Hi Can you tell me what area of coverage will I get from one litre of the super adhesion primer please? Thanks Amanda |
Answer from Rawlins’ Technical Team: The theoretical coverage for Rust-Oleum 3333 Super Adhesion Primer is 41m²/litre | |
| claire on 2018-07-23 22:57:33 | Question: I have some clay tiles (like quarry tiles but says made of clay) I have old quarry tiles cleaned and sealed but the new ones in clay don't hold the sealer. It easily comes off with bare feet or if it gets wet with washing up water etc in kitchen. Should I apply a clear primer over the top of the sealant that has just been put on for the 3rd time or which primer would you suggest? Is there a clear primer/ sealant which would stick to the tiles please and provide protection. Gloss preferably as the old quarry tiles have been gloss sealed. thanks |
Answer from Rawlins’ Technical Team: Our best recommendation for this would be to remove all existing coatings and try a test area with Rust-Oleum 4900 Polycoat 2K to ensure it is suitable before coating the whole area. | |
| Sharon on 2017-01-12 08:04:05 | Question: Hi could you tell me the difference between Rust-Oleum super adhesive primer 333 and and the 333 handy pack.Thanks,Sharon |
Answer from Rawlins’ Technical Team: There is no difference between the products, the Handy Pack has been developed to make one off smaller projects easier with more user friendly packaging and instructions. | |
Rust-Oleum 3333 Super Adhesion Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. Rust-Oleum FK111 Cleaning Solution is a concentrated, alkaline, non-flammable, virtually odour free cleaning and degreasing solution for vertical...
General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site.Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects Click to jump down to...
£12.04 (incl. VAT)
£10.03 (ex. VAT)
Floor Application Kit from Rawlins Paints provides all the application equipment needed to apply conventional floor paints and coatings to a professional standard. The application of floor coatings is often crucial to their performance, so it is important to use the right tools to ensure a lasting finish.Each kit contains:12" Roller,...
£101.58 (incl. VAT)
£84.65 (ex. VAT)
