Watco Powerfloat Sealer

    Watco-PS
    WAT9195

    Seals and protects power floated floors, specially formulated for smooth, power floated or glazed concrete.

    • No need for expensive mechanical floor preparation
    • Retains the attractive, smooth floor surface
    • Tough, easy clean epoxy resin formulation
    • Anti-slip version also available - excellent slip resistance

    Coverage Calculator

    Colour
    Item
    Size
    Finish
    £116.75(ex. VAT)
    £140.10 (inc. VAT)
    Quantity
    Please choose your colour
    Available for Delivery (See Delivery Options Below)

    Description

    This clear, water based epoxy sealer stops dust, reduces staining and makes very smooth or power floated concrete easier to clean. Unlike other sealers, the floor does not need to be shot blasted or etched before application, as the sealer has been specially designed to adhere to non-porous surfaces. If at a later date you decide you want to paint your floor with one of our coatings, you can just paint over the top of the sealed surface with minimal surface preparation. Watco Powerfloat Sealer is available with either a gloss or matt finish and there is also a finely textured anti slip version of both.



    Quick Links - Click To Jump To Section:




    Features & Benefits


    • Apply direct to power floated or smooth non-porous concrete
    • No need for expensive mechanical floor preparation
    • Retains the attractive, smooth floor surface
    • Tough, easy clean epoxy resin formulation



    Surface Preparation


    New concrete should be allowed at least 28 days to dry. Surfaces should be clean, dry and free from oil, grease, dust, dirt and other contaminants.



    Mixing


    The tall outer tin contains a tin of Resin and a tin of Curing Agent. Remove these two tins and stir the contents of each thoroughly. Decant both tins into the tall outer tin. The two components should then be very thoroughly mixed together using a wide bladed stirrer. A wooden batten at least 25mm wide is ideal. Mix for 2-3 minutes until an even consistency is obtained. Both liquids are opaque white/off white in colour and it is important to ensure complete mixing to allow the cure reaction to happen.

    The resin component of Powerfloat Sealer Anti Slip contains a pre-blended aggregate.



    Application


    Decant the mixed components into a roller tray and apply using a medium pile type roller. A brush may be used for cutting in.

    Important – apply to a well ventilated area of no less than 40m2. If this product is applied too thickly and/or the area is not sufficiently ventilated to allow a ‘through’ draught, it could fail to dry from white to clear.

    Aim to apply the mixed components within one hour (they are useable for up to 2 hours maximum at 20°C). Do not apply at temperatures below 10°C or above 30°C. Cold or damp conditions may retard or prevent full curing. The two components for Powerfloat Sealer and Powerfloat Sealer Anti Slip are white, but the coating will cure to a clear finish within 2 hours.



    Limitations


    Please contact us regarding applications not described here.

    Unsuitable for bare metal.

    Most self-levelling compounds cannot be painted — please ask for details.



    Product Details
    9195-946312

    Data sheet

    Manufacturer
    Watco
    For Use By
    Consumer Use
    Interior / Exterior Use
    Interior Use
    For Use On
    Concrete
    Application Method
    Medium pile roller. Cut in using a brush.
    Single, Two or Three Pack
    Two-Pack
    Pack Size
    5L
    Coverage
    Approximately 40m² per 5 litres
    Recommended Thinner/Cleaner
    Warm soapy water
    Min. Application Temperature
    Air Temperature 15°C.
    Floor Temperature 10°C.
    Finish
    Matt and Gloss
    UN Number
    UN3066 (Curing Agent)
    Pot Life
    Up to 2 hours at 20°C
    Fully Cured
    Approximately 16 hours at 15°C - 20°C for general traffic.
    Base Type
    Water-Based
    Suitable For Use On
    Concrete Floors
    Suitable For Use On
    Concrete
    Finish
    Gloss
    Finish
    Matt
    Application Method
    Roller
    Components
    2K
    Product Usage Type
    Sealer
    Product Range
    Powerfloat
    Product Range
    Watco Specialist
    Colour Family
    Clear
    Anti-Slip Texture
    Fine Texture
    Product Type
    Epoxy
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    Watco Powerfloat Sealer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    COVERAGE CALCULATOR
    Units
    Total area²
    Or enter length and width dimensions:
    Length
    Width

    *All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage