403 Oil Tolerant Primer has been developed for use in applications to oil contaminated floors prior to application of subsequent floor toppings. The product exhibits outstanding adhesion to concrete and other substrates and is particularly suitable where compromised surfaces exist.
Solvent free, low odour
Excellent adhesion to concrete and steel
Surface tolerant
Excellent wetting properties
Low viscosity, easily applied
Pre-packaged units ready for use
Images are for illustrative purposes only and may differ from the actual product
403 Oil Tolerant Primer has been developed for use in applications to oil contaminated floors prior to application of subsequent floor toppings. The product exhibits outstanding adhesion to concrete and other substrates and is particularly suitable where compromised surfaces exist.
403 Oil Tolerant Primer is supplied as a two pack system, comprising pre-weighed amounts of base and curing agent components.
Recommended for use as a primer for oil contaminated concrete or steel prior to the application of our Epoxy Floor Coatings or Screeds.
Recommended for use as a primer for oil contaminated concrete or steel
Two-pack
Outstanding adhesion to concrete and other substrates
Solvent free, low odour
Surface tolerant
Excellent wetting properties
Low viscosity, easily applied
Pre-packaged units ready for use
Typical Properties
Technical Data
403 Oil Tolerant Primer
Viscosity:
600-800 cps @ 20°C
Pot life @ 20°C:
60 Minutes
Pot life @ 10°C:
90 minutes
Adhesion to concrete:
3.8 MPa (concrete failure)
Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for specific advice.
Coverage
2.0 - 3.3m²/Kg depending on surface texture
Surface Preparation
New concrete surfaces shall be a minimum of 7 days old
Old oil-contaminated concrete surfaces shall be washed with detergent and water and allowed to dry
Suitable mechanical treatment such as vacuum grit blasting or mechanical scabbling are recommended to ensure the removal of contaminants
Mixing:
403 Oil Tolerant Primer is supplied in pre-weighed containers ready for mixing
Pour the contents of the curing agent tin into the base container and thoroughly mix, preferably by mechanical means until a uniform colour is achieved
Mixing Ratio:
By Volume - 1.94 Base : 1 Curing Agent
By Weight = 100 Base : 48.8 Curing Agent
Application
Apply by brush, roller or squeegee to the prepared surface at a nominal rate of 0.3 to 0.5Kg/m²
Ensure that the surface is thoroughly wetted out
If the primer is to be allowed to cure prior to overcoating, then it is permissible to broadcast 0.4-0.7mm 504 Standard Anti-Slip Aggregate into the wet primer to assist subsequent adhesion of our Epoxy Coatings
Our Epoxy Screeds and Mortars may be applied to the wet primer
Cleaning
Clean equipment with 109 Tool Cleaner prior to curing of the coating
Curing
Touch dry after 8 hours @ 20°C
Hard dry after 16 hours @ 20°C
Limitations
Do not apply to temperatures below 3°C, or if there is a risk of frost during the initial curing period
With severely contaminated old concrete it is recommended that a pull off adhesion test be carried out prior to full scale application
Storage & Shelf Life
Store in dry conditions at temperatures between 10°C and 25°C
Do not expose to freezing conditions
403 Oil Tolerant Primer has a minimum 12 months shelf life when stored in original, unopened containers in accordance with manufacturer’s instructions
403 Oil Tolerant Primer shall be applied strictly in accordance with the manufacturer’s instructions
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
403 Oil Tolerant Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
504 Standard Anti Slip Aggregate is a specially formulated quartz aggregate to be added to various products in our floor coatings range to provide increased `anti-slip` properties in both dry and wet conditions to improve safety.
Produces a rough, non-skid surface
Hard wearing and chemical resistant
Coloured Quartz Aggregate 0.4-0.8mm...
109 Tool Cleaner is a specialist equipment cleaner suitable for the removal of uncured epoxy, polyester and polyurethane resins.
Low Hazard
Low evaporation rate
Excellent solvency powers
80% biodegradable
This product is for Professional Use Only
Images are for illustrative purposes only and may differ from the actual product
More...
