1L Pack
  • 1L Pack
  • 5L Pack
  • 404 Epoxy Metal Primer

404 Epoxy Metal Primer

RAW404

404 Epoxy Metal Primer is a two pack, water-based, epoxy, anti-corrosive primer designed for the protection of steelwork.

  • Non toxic
  • Fast drying - touch dry in 1-2 hours @ 20ºC 
  • May be applied to damp or dry surfaces
  • Excellent anti-corrosive properties
  • Compatible with a wide range of top coats
  • Long overcoating window
  • Easily applied
  • Very good adhesion
  • Early water resistance
  • Good chemical resistance
  • Images are for illustrative purposes only and may differ from the actual product
  • This product is for Professional Use Only

**Available for delivery - see Delivery Options below**

Colour
Size
£29.48
VAT excluded

£35.38 Tax incl.
Quantity

Description

404 Epoxy Metal Primer is a two pack, water-based, epoxy, anti-corrosive primer designed for the protection of steelwork. Whilst optimum performance will only be achieved by applying to well prepared substrates, 404 Epoxy Metal Primer will adhere well to minimally prepared surfaces.

404 Epoxy Metal Primer has been formulated to provide fast touch dry times and rapid hardness development.

Recommended for use as an anti-corrosive primer for steelwork, and also as a holding primer for grit blasted steel surfaces.

This product is for Professional Use Only.



Quick Links - Click To Jump To Section:




Features & Benefits


  • Water-based
  • Two-pack
  • Non toxic
  • Fast drying
  • May be applied to damp or dry surfaces
  • Excellent anti-corrosive properties
  • Long overcoating window
  • Easily applied
  • Very good adhesion
  • Early water resistance
  • Good chemical resistance



Typical Properties


Technical Data
  404 Epoxy Metal Primer
Volume solids: 60%
Specific Gravity: 1.46
Pot life: 2 hours @ 20ºC
Touch Dry: 1-2 hours @ 20ºC
Hard Dry: 4 hours @ 20ºC
Full Cure: 7 days @ 20ºC
Overcoating at 20ºC: Minimum 4 hours, maximum 2 months



Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for specific advice.



Coverage


  • 1 litre of 404 Epoxy Metal Primer will be sufficient to treat 4-6m² of surface, achieving an overall dry film thickness of 100-150 microns



Surface Preparation


Steel/Galvanised steel:

  • Any rust, mill scale and other contaminants should be removed by gritblasting to Swedish Standard Sa 2.5
  • Reduced levels of surface preparation, e.g. wire brushing to remove loose rust, are permissible, but may lead to lower performance levels



Mixing:

  • Mix the two components together, preferably by mechanical means, until a uniform consistency has been achieved



Mixing Ratio:

  • By Volume - 1 Base : 1 Curing Agent
  • By Weight - 62.2 Base : 100 Curing Agent



Application


  • Apply the material by brush, roller or airless spray, at a nominal rate of 4-6m² per litre per coat



Cleaning




Curing


  • Following 4 hours cure @ 20ºC the material will be hard dry, and then may be re-coated
  • Allow 7 days cure @20ºC for optimum chemical resistance and mechanical properties
  • The primer may be allowed to age and weather for a maximum period of up to 2 months prior to top coating



Limitations


  • Do not apply to wet surfaces
  • Do not apply at temperatures of 3°C or less



Storage & Shelf Life


  • Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 25°C
  • Avoid frost
  • 404 Epoxy Metal Primer has a minimum shelf life of 12 months when stored in original, unopened containers in accordance with manufacturer’s instructions



Health & Safety


  • Avoid contact of the material with skin and eyes
  • Wear gloves and goggles
  • Wash off splashes immediately with soap and water
  • Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought
  • Please refer to Material Safety Data Sheet for additional information
  • 404 Epoxy Metal Primer shall be applied strictly in accordance with the manufacturer’s instructions

For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]



Product Details
RAW404

Data sheet

Water / Solvent Based
Water
For Use On
Steel
Application Method
Brush, Roller, Airless Spray
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Two-Pack
Touch Dry (at 20°C)
1-2 Hours
Dry to Recoat (at 20°C)
Minimum 4 hours, Maximum 2 months
Fully Cured (at 20°C)
7 days
Pot Life (at 20°C)
2 Hours
Coverage
5m² per litre
Touch Dry
8 Hours
UN Number
Not Regulated
Specific Gravity
1.46
Hard Dry
4 hours @ 20ºC
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

109 Tool Cleaner

109 Tool Cleaner is a specialist equipment cleaner suitable for the removal of uncured epoxy, polyester and polyurethane resins. Low Hazard Low evaporation rate Excellent solvency powers 80% biodegradable This product is for Professional Use Only Images are for illustrative purposes only and may differ from the actual product Click to...

Price £30.62
In stock