RSL Resucoat GC

SCSEB

RSL Resucoat GC (formerly known as R.S Screed Seal) is a two-pack epoxy resin surface coating for use with other RSL and Sherwin-Williams products, filling any voids, pockets or interstices exposed in the surface. 

Features and Benefits: 

  • Enhances chemical resistance
  • Prevents water spillage
  • Improves cleanability
  • Hygienic
  • No shrinkage on curing
  • Can be used decoratively
  • Colour stability 
Colour
Size
Finish
£82.00
VAT excluded

£98.40 Tax incl.
Quantity

Description

For optimum results, Resucoat GC (formerly known as R.S Screed Seal) should be used with Resuscreed 45, Resuscreed 55, and Resuscreed QS - all Resin Surfaces Limited products.

Recommended Uses

  • Food and beverage sites
  • Factories
  • Warehouses
  • Engineering environments
  • Garages/Showrooms
  • Aviation hangars 

Preparation

The surface to be treated with Resucoat GC must be clean, sound, dry and fully cured. Rates of coverage will be affected by the particle size and the density of packing achieved during the application of the screed. Open textures will reduce rates of coverage significantly.

Application

The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance of the system. Surface temperature must be above 10°C.

Where possible it is recommended that the application area is heated to a minimum temperature of 15°C to allow the ambient and substrate temperature to stabilise prior to installation.

Mixing: Pre-mix the base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used, mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two minutes or until the two components have fully combined.

Resucoat GC is highly thixotropic, careful and thorough mixing is required. For trowel and squeegee application, de-nibbing of the surface by steel trowel is recommended prior to application.

Resucoat GC should be applied within 48 hrs of the application of the screed system. Apply to the clean surface with a polypropylene squeegee. Ensure that the Resucoat GC is forced into the surface of the resin screed and pull down any excess to leave a thin coating. Finally, roller off to achieve an even film finish. Resucoat GC does not tend to flow, therefore it is important to ensure that the finish is to an acceptable standard whilst wet.

When Resucoat GC is being used on coloured systems, after an overnight cure apply a coat of Resucoat HB to provide a wearing finish.

When Resucoat GC is being used on decorative systems, after an overnight cure apply a coat of Resutop Clear to provide a wearing finish.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
SCSEB

Data sheet

Manufacturer
RSL
Interior / Exterior Use
Interior
Water / Solvent Based
Solvent
For Use On
Concrete
Application Method
Squeegee, Roller, Trowel
Sheen
Smooth Gloss
Colour
Clear
VOC Levels
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Two-Pack
Pack Size
5KG
Application
Squeegee, Roller.
Coverage
5kg will cover 12m sq. @ 360 microns DFT.
Touch Dry
8-10 Hours
UN Number (Activator)
UN3066
UN Number (Base)
UN3082
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

RSL Resuscreed QS

Resuscreed QS, formerly known as Decora MS, is a decorative epoxy resin floor screed incorporating multi-coloured aggregates, designed to produce a hard wearing, attractive, impervious sealed surface, sealed with clear resins to provide a matt or gloss finish. More aggregate can be bought by adding RSL Resuscreed QS Aggregates only to your...

Price £90.00
In stock

RSL Resuscreed 45

Resuscreed 45 is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish. ADVANTAGES Less dust than other screeds Low odour Hard wearing Abrasion and impact resistant Can form coving and falls Can be feather edged Can act as a...

Price £59.30
In stock

RSL Resuscreed 55

Resuscreed 55 is a flecked epoxy resin floor screed for concrete, wood metal and other surfaces with sound and clean substrates. It produces a seamless finish to new and existing floors. ADVANTAGES Hard wearing Can be a repair system Feather edged option Low odour Can be used to form coving and falls Abrasive/Impact resistant See...

Price £68.09
In stock

RSL Resutop Clear

Resutop Clear is a two-pack, high solids, high-build epoxy coating for application as a chemical resistant heavy duty floor coating, used as a clear sealer for decorative flooring systems such as Decora MS, producing a seamless, hard wearing, hygienic floor finish. Low odour Good colour stability Excellent slip resistance with the use of...

Price £67.88
In stock