

Britannia Concrete Floor Sealer is a single pack acrylic solution for dustproofing concrete floors. Ideal for factories, warehouses, kitchens, food processing areas, garages, workshops, production and plant areas.
Britannia Concrete Floor Sealer is a single pack acrylic formulation concrete dustproofer, with low viscosity for excellent penetration into the pores of the substrate. Designed to penetrate and bind concrete, sand/cement floor screeds, blockwork and rendered walls. Produces a dust-free concrete surface with a subtle sheen.
Ideal for treatment of dusting concrete floors in factories, warehouses, kitchens, food processing areas, garages, workshops, production and plant areas.
These will vary depending on substrate, the site conditions and longevity required.
Typically spreading rates will vary depending on the end use.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
![]() | Question:
can this product be painted over (for line markings only) and can be classed as non or low slip can be contacted on 07860 776065 |
Answer:
This product is not suitable to be over painted and does not provide a level of anti-slip. | |
![]() | Question:
i have a concrete slab in an unheated building that was poured 21 days ago. is this product suitable to be applied now to prevent concrete dust and provide oil and petrol resistance |
Answer:
Assuming the concrete slab is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend 401 Epoxy Floor Primer. Temperature for application should be between 10°C and 30°C. For temperatures as low as 5°C 401 WG Epoxy Floor Primer can be used. | |
![]() | Question:
Is this product for external use on a crossing which some of the aggregate has become exposed? The concrete was laid 3 years ago and the crossing is 24 m2. |
Answer:
Britannia Concrete Floor Sealer is not suitable for exterior use as a finish, our 314 Clear Floor Sealer can be used externally but we would require more information on what the 'crossing' is and what type of traffic it recieves to be able to confirm suitability. Please contact our Technical Team on 0113 2455450 (option 2) or [email protected] with more information. | |
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.