Rust-Oleum 5220 Epoxyshield® Sealer is a one-component, water-based, concrete sealer based on a vinyl acrylic binder. It reduces dust production, protects the floor against liquid/chemicals and simplifies cleaning. It is cost-effective, quick drying, easy to apply and available to order from Rawlins Paints.
Water based, cost-effective, quick drying
Single pack, easy to apply
Non-yellowing clear finish (gloss)
Protects against moisture and road salts
Touch dry after just 1 hour
Ideal primer for EpoxyShield® ULTRA coatings
Reduces dust production on concrete
Protects against liquid and chemical spills
Suitable for garage floors
Cost-effective
Quick drying and easy to apply
Recommended Use
When EpoxyShield® Sealer is used as a finish, apply 2 coats. EpoxyShield® Sealer can also be used as a sealer/impregnation primer for EpoxyShield® 5200 ULTRA. Apply the sealer on bare and clean concrete floors. Apply the product only on fully clean and dry concrete surfaces. Do not apply on smooth or very dense concrete or concrete which contains curing compound.
Technical
Density: 1,02
Gloss Level: Gloss
Solids content in volume: 30%
Drying Times At 20°C/RH 50%
Touch dry: approximately 1 hour
Theoretical Consumption
Maximum 10 m² per litre.
Practical Consumption
Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.
Temperature of air, substrate and coating material between 10 and 35°C, relative humidity below 85%. The substrate temperature must be at least 3°C above dew point. Ventilate well during and after application.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Can this product be used over a floor that has been sealed using Blackfriar Professional Water Based Floor Sealer?
Answer from Rawlins’ Technical Team:
No this product is design to be applied to bare concrete floors to reduce dust and protect the floor from liquids.
It can be used as a finishing coating but only to bare concrete.
G on 2019-11-14 07:25:32
Question:
Morning, I would like to have a clear finish on my new kitchen floor - which was levelled with a self-levelling screed. Is the Rust-Oleum 5220 EpoxyShield Sealer appropriate to use on this type of floor i.e. in such a high traffic area. Thank you.
Answer from Rawlins’ Technical Team:
Rust-Oleum 5220 Epoxyshield Sealer could be used for this type of application however we would suggest you ensure the self levelling screed used is suitable to be left as a wearing course to recieve the level of expected traffic and that it can in fact be overcoated with Rust-Oleum 5220 Epoxyshield Sealer. You would need to contact the Technical Department of the manufacturer of the screed to ascertain this information, presenting them with the data sheet of Rust-Oleum 5220 Epoxyshield Sealer.
Alan James on 2019-06-29 08:00:20
Question:
Hi, We wish to waterproof and harden the concrete floor of a garage for parking motorcycles. We ride in all weathers and so sometimes come home with wet bikes. We also do some maintenance so there are occasional small oil spills. Concrete was poured 3 months ago, with an area of about 25 sq m. Can you advise the best product please. Many thanks.
Answer from Rawlins’ Technical Team:
Rust-Oleum 5220 Epoxyshield Sealer could be considered for this purpose, but given that the mention of frequent water and occasional oil spillages, we would instead advise 2 - 3 coats of Rust-Oleum 4900 Polycoat 2K.
Chris on 2018-12-14 21:53:12
Question:
I’ve just finished grinding the surface of a recently laid concrete floor in my extension. I used a diamond grinding disc attached to an angle grinder which has removed all ridges, but I’ve stopped short of polishing it. Would this product be suitable in my floor please? Thanks
Answer from Rawlins’ Technical Team:
Diamond grinding is an excellent method of preparation for concrete prior to applying Rust-Oleum 5220 Epoxyshield Sealer. Ensure the concrete is completely clean and dry before application. New concrete should be allowed to cure for at least 30 days minimum.
P Storey on 2018-05-13 11:42:38
Question:
I'm thinking of sealing my garage floor using Rust-Oleum 5220 Epoxyshield Sealer. Can I apply a standard floor paint on top of the Sealer? Thanks.
Answer from Rawlins’ Technical Team:
After application of Rust-Oleum 5220 Epoxyshield Sealer if a coloured topcoat is required we recommend Rust-Oleum 5200 Epoxyshield Ultra is used.
Tom lester on 2018-02-04 13:15:59
Question:
Can l lay underlay and carpet on top of this product
Answer from Rawlins’ Technical Team:
Yes once Rust-Oleum 5220 Epoxyshield Sealer has fully cured.
PJ on 2018-02-01 21:39:55
Question:
Hi I would like to have a clear finish on my new kitchen extention concrete floor which has been power floated. Is this EpoxyShield Sealer appropriate to use on this floor and in such a hi traffic area (using the two coats recommended) many thanks
Answer from Rawlins’ Technical Team:
Rust-Oleum 5220 Epoxyshield Sealer cannot be applied on smooth or very dense concrete or concrete which contains curing compound. As this is a power floated floor it would limit the adhesion that may be obtained between substrate and paint. This would also be true for any alternatives we might consider.
We can of course provide a clear hard wearing floor system, but in order to do so, you would need to “open up” the surface by way of grinding or blasting and whilst this would assist with the adhesion, the consequence of course would be removing the very smooth appearance.
If you are happy with this compromise we would then recommend the application of something like Rust-Oleum 4900 Polycoat 2K instead. However we would recommend carrying out a trial first to ensure adhesion, appearance, performance, etc. are all acceptable.
Rust-Oleum 5220 Epoxyshield Sealer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
Rust-Oleum 5200 Epoxyshield Ultra is a 5 litre, satin finish, quick-drying single pack water-based floor coating for garage floors, and light to medium duty (normal foot traffic/limited vehicular traffic):
Part of the Epoxyshield range
Good resistance to diesel, motor oil, coolant fluid, various household chemicals and most types of tyre...
Floor Application Kit from Rawlins Paints provides all the application equipment needed to apply conventional floor paints and coatings to a professional standard. The application of floor coatings is often crucial to their performance, so it is important to use the right tools to ensure a lasting finish.
Each kit contains:
12" Roller,...