• 701 MMA Floor Coating

    701 MMA Floor Coating

    RAW701
    RAW1118

    701 MMA Floor Coating is a two pack, fast curing coating designed to provide a dust-free, seamless floor finish with protective and decorative properties on concrete and steel surfaces. The inherent slip resistance of the coating may be enhanced by the incorporation of 504 Standard Anti Slip Aggregate.

    • Also available in 4,000+ colour options from RAL, BS and NCS
    • Tough and abrasion resistant
    • Colour stable
    • Very good chemical resistance
    • Rapid curing minimises down times and ensures a fast return to service
    • Accepts light foot traffic in 1 hour @ 20°C
    • Suitable in wet areas
    • Hygienic and easily cleaned
    • Cures at low temperatures (as low as -20°C)
    • Hot water and fat resistant to 80°C
    • Images are for illustrative purposes only and may differ from the actual product
    • This product is for Professional Use Only

    Product customisation

    Don't forget to save your customization to be able to add to cart
    • 250 char. max
    Colour Group
    Size
    Finish
    £112.00(ex. VAT)
    £134.40 (inc. VAT)
    Quantity
    Please choose your colour
    Available for Delivery (See Delivery Options Below)

    Description

    701 MMA Floor Coating is a two pack, fast curing coating designed to provide a dust-free, seamless floor finish with protective and decorative properties. The inherent slip resistance of the coating may be enhanced by the incorporation of 504 Standard Anti Slip Aggregate.

    701 MMA Floor Coating can be trafficked after just 1 hour (see ‘curing’ for full details), allowing a fast return to service and can be applied at temperatures as low as -20°C.

    This product is for Professional Use Only.

    Recommended Uses:

    • As a rapid curing, abrasion and chemical resistant floor coating where minimal downtime is paramount



    Quick Links - Click To Jump To Section:




    Features & Benefits


    • Can be applied at temperatures as low as -20°C
    • Tough and abrasion resistant
    • Can be trafficked after just 1 hour
    • Colour stable
    • Very good chemical resistance
    • Two-pack
    • Rapid curing minimises down times and ensures a fast return to service
    • Suitable in wet areas
    • Hygienic and easily cleaned
    • Hot water and fat resistant to 80°C



    Typical Properties


    Technical Data
     701 MMA Floor Coating
    Pot life @ 20°C: 15-20 Minutes
    Pot life @ 10°C 25-30 minutes
    Tensile strength: 20N/mm²
    Elongation at break: 2%
    Flexural strength:37N/mm²
    Adhesion to concrete: 3.8N/mm² (concrete failure)
    Adhesive strength to grit blasted steel: 12N/mm²
    Temp. range during application:-20°C to + 40°C
    Temp. range during service: -20°C to + 80°C



    Chemical Resistance
    ChemicalResistance
    Dilute Acids and AlkalisExcellent
    OilExcellent
    PetrolExcellent
    DieselExcellent
    Vegetable OilsExcellent
    Fruit JuicesExcellent



    Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for specific advice.



    Coverage


    • A 5kg pack is sufficient to cover an area of 8.3m² with the recommended two coat treatment, providing a minimum thickness of 500 microns



    Surface Preparation


    • Concrete surfaces shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%
    • Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound, and existing paint finishes, etc
    • Blow holes and defective concrete shall be made good using 710 MMA Repair Mortar
    • Suitable mechanical treatment, such as vacuum grit blasting, is the preferred treatment prior to application as this ensures a mechanical ‘key’ which will optimise adhesion
    • Steel surfaces shall be shot blasted or grit blasted to a nominal Sa 2.5 Swedish Standard
    • All dust shall be removed prior to coating application. A coat of 707 MMA Metal Primer shall be applied as soon as practicable after blasting, in order to obviate the possible occurrence of ‘flash rusting’



    Priming:

    • Concrete surfaces shall be primed with a coat of 706 MMA Floor Primer, applied by brush or roller, at a nominal rate of 0.3kg/m²
    • Long nap lambswool rollers are recommended for primer application
    • Allow primer to cure for a minimum of 40 minutes
    • Steel surfaces shall be primed with 707 MMA Metal Primer as soon as practicable after blasting
    • Damp concrete surfaces can be primed using 709 MMA Damp Proof Primer – refer to product data sheet for full details



    Mixing:

    • 701 MMA Floor Coating is supplied as a two pack material consisting of the base component, and the catalyst component, incorporate the catalyst component into the base component under mechanical stirring, and mix for 1-2 minutes



    Mixing Ratio:

    • (% Catalyst by Weight) = 1.8



    Application


    • Apply 701 MMA Floor Coating using short nap perlon, or smooth lambswool rollers at a nominal rate of 0.30kg/m²
    • Following a minimum of 1 hour apply a second coat at the same nominal rate
    • Should a slip resistant or skid resistant finish be required then broadcast 504 Standard Anti Slip Aggregate onto the first coat within 10 minutes of application
    • Following a minimum of 1 hour, sweep off excess aggregate and apply a second coat of 701 MMA Floor Coating

    Note: 701 MMA Floor Coating may be applied at greater thicknesses should service conditions warrant it.



    Cleaning




    Curing


    • Light Foot Traffic: 1 hour @ 20°C
    • Vehicular Traffic: 2 Hours @ 20°C
    • Full chemical resistance: 24 hours @ 20°C



    Limitations


    • Do not apply to wet, uncured or un-primed concrete surfaces

    701 MMA Floor Coating will taint food during application, so that all foodstuffs in the immediate vicinity must be removed or properly covered



    Storage & Shelf Life


    • Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 20°C
    • Adequate ventilation of the storage area should be provided
    • Keep container tightly closed when not in use
    • 701 MMA Floor Coating has a minimum shelf life of 6 months when stored in original, unopened containers in accordance with manufacturer’s instructions



    Health & Safety


    701 MMA Floor Coating is flammable during application, so adequate safety precautions should be observed.

    • Avoid contact of the material with skin and eyes
    • Wear gloves and goggles
    • Wash off splashes immediately with soap and water
    • Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought
    • Please refer to Material Safety Data Sheet for additional information
    • 701 MMA Floor Coating shall be applied strictly in accordance with the manufacturer’s instructions

    For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]



    Product Details
    1118-863045

    Data sheet

    Manufacturer
    Rawlins Paints
    For Use By
    Professional Use
    Interior / Exterior Use
    Interior Use
    Water / Solvent Based
    Solvent
    For Use On
    Concrete, Steel
    Colour
    Standard / Ready Mixed
    Single, Two or Three Pack
    Two-Pack
    Product Certifications
    Sa 2.5 Swedish Standard
    Pack Size
    5KG
    Coverage
    3.2m² per KG
    Tensile Strength
    20N/mm²
    Max. Application Temperature
    40°C
    Min. Application Temperature
    -20°C
    Touch Dry
    1 Hour
    UN Number (Activator)
    UN3106
    UN Number (Base)
    UN1866
    Elongation at break
    2%
    Base Type
    MMA
    Base Type
    Solvent-Based
    Suitable For Use On
    Steel
    Suitable For Use On
    Concrete
    Finish
    Satin
    Application Method
    Roller
    Components
    2K
    Product Usage Type
    Topcoat
    Product Category
    Paints
    Colour Family
    Green
    Colour Family
    Red
    Colour Family
    Black
    Colour Family
    Grey
    Colour Family
    Blue
    Colour Family
    Yellow
    Colour Family
    White
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    701 MMA Floor Coating is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    504 Standard Anti Slip Aggregate

    504 Standard Anti Slip Aggregate is a specially formulated quartz aggregate to be added to various products in our floor coatings range to provide increased `anti-slip` properties in both dry and wet conditions to improve safety.Produces a rough, non-skid surface Hard wearing and chemical resistant Coloured Quartz Aggregate 0.4-0.8mm...

    Price £8.00 (ex. VAT)
    In Stock and Available for Delivery

    706 MMA Floor Primer

    706 MMA Floor Primer is a rapid curing, general purpose primer enabling fast overcoating. The product exhibits outstanding adhesion to concrete, as well as steel, masonry, and marine plywood, and the fast curing characteristics allow rapid application of subsequent coatings, mortars or screeds.Ideal for use as a rapid curing primer for...

    Price £112.00 (ex. VAT)
    In Stock and Available for Delivery

    707 MMA Metal Primer

    707 MMA Metal Primer is a rapid curing three-pack primer for steel, galvanised steel, aluminium, and unglazed ceramic tiles to be used prior to any of the MMA range of coatings, mortars, and screeds.Rapid cure, even at low temperatures - from as low as -30°C* Very good corrosion resistance Excellent adhesion Impervious to water...

    Price £112.00 (ex. VAT)
    In Stock and Available for Delivery

    709 MMA Damp Proof Primer

    709 MMA Damp Proof Primer has been developed as a primer for damp concrete, being used prior to any of our MMA range of coatings, mortars, and screeds.Rapid cure, even at low temperatures - from as low as -30°C* Very good chemical resistance Excellent adhesion to damp concrete Impervious to water Pre-packed units ready for use Easily...

    Price £112.00 (ex. VAT)
    In Stock and Available for Delivery

    710 MMA Repair Mortar

    710 MMA Repair Mortar is a fast curing, high strength, trowel applied, three component methacrylate resin mortar, designed for rapid and permanent repairs to concrete and masonry surfaces.Resilient Very good chemical resistance Excellent adhesion Fast curing, even at low temperatures (down to -10°C*) Impact and abrasion resistant...

    Price £76.80 (ex. VAT)
    In Stock and Available for Delivery

    109 Tool Cleaner

    109 Tool Cleaner is a specialist equipment cleaner suitable for the removal of uncured epoxy, polyester and polyurethane resins.Low Hazard Low evaporation rate Excellent solvency powers 80% biodegradable This product is for Professional Use Only Images are for illustrative purposes only and may differ from the actual productMore...

    Price £44.00 (ex. VAT)
    In Stock and Available for Delivery