Rust-Oleum 5800 Epoxy Rapid WB is a fast curing epoxy floor paint for inside use. For garages, warehouses, showrooms, corridors, indoor car parks, workshops etc.
Rust-Oleum 5800 Epoxy Rapid WB
Rapid curing epoxy floor paint for inside use. For garages, warehouses, showrooms, corridors, indoor car parks, workshops etc.
Rust-Oleum® Epoxy Rapid WB 5800 can be applied on cleaned, sound mineral substrates, sound and well prepared previous coatings. The product can be applied directly on porous substrates; a special primer is not needed.
Technical Data
Drying Times At 20°C/RH 50%
Theoretical Consumption
6 m²/l
Practical Consumption
Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.
Surface Preparation
Concrete must be at least 30 days old, completely dry and free of surface laitance, contaminants and previous poorly bonded coatings. Remove grease, oil and all other surface contaminations by alkaline or high pressure (steam) cleaning in combination with appropriate detergents. Sand previous coatings which are in good condition to remove gloss and to roughen the surface slightly, check compatibility. Very smooth concrete or concrete with surface laitance (a weak dusty layer) should be abraded or etched with Surfa-Etch 108 to ensure adequate adhesion. The concrete should be thoroughly washed down and allowed to dry after. Powerfloat Epoxy Floor Primer 3366 is recommended on powerfloated surfaces.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
 Terry Richards on 2017-11-09 21:40:22 | Question: Hi, I have a new 28 square meter concrete garage floor, please advise: 1. how long should I allow concrete curing time before painting? 2. Quantity & product to clean, prepare floor? 3. Quantity & product to pre seal floor? 4. Quantity & product to paint floor & number of coatings? The rear garage wall is floor to ceiling double glazed units and paint product will therefore need to tolerate high levels UV light without dis-colouring over time. Thank you for your assistance. |
Answer from Rawlins’ Technical Team: Blackfriar Professional High Traffic Floor Paint is an exceptionally hard-wearing, high performance, easy-to-clean 2-pack solvent based floor coating ideal for indoor and outdoor use. Provides outstanding resistance to a wide range of chemicals. Non-yellowing, excellent colour fastness. Preparation Ensure the surface to be painted is sound, clean, dry and free from grease or any substance liable to give adhesion problems. Scrape off any old or flaking paint until you have a firm surface. Special attention should be given to areas under cars to ensure all oil, grease, dirt and road salt is removed. Prepared surfaces with residual oil contamination should be primed with Blackfriar Professional Oil Tolerant Primer. New concrete must be left for at least 6 months before applying Blackfriar Professional High Traffic Floor Paint. Power-floated floors should either be blast tracked or treated with Blackfriar Professional Acid Etch followed by thorough rinsing. New or exposed bare concrete should be primed with Blackfriar Professional Water Based Epoxy Floor Primer. Based on 28m² (assuming your floor is NOT power-floated) you would require; 1 x 5L Blackfriar Professional Epoxy Floor Primer | |
| Rob Jones on 2017-10-09 08:56:22 | Question: Hi there, I have a worn out garage floor that has previously been painted but now the paint has worn and lifted in places. I keep getting white powder building up even though I have tried different sealers. If I coat the floor with Everbuild 908 DPM to stop the damp rising, can I then coat with epoxy paint and if so which one would be most suitable? Or do you have a product that would do both? |
Answer from Rawlins’ Technical Team: Remove all existing coating from floor and apply 402 Damp Proof Coating. Download all product data sheets from the 'DATASHEETS' tab and read thoroughly before use. | |
Rust-Oleum 5800 Epoxy Rapid WB is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Rust-Oleum Powerfloat Epoxy Floor Primer Rapid 3366 is a rapid curing, 2-component epoxy primer designed to improve the adhesion of coatings to difficult substrates such as power-floated concrete.Overcoatable after just 3 hours: apply primer and topcoat in one day Easy all-in-1 packaging For new and aged power floated concrete, even with...
£162.47 (incl. VAT)
£135.39 (ex. VAT)
Rust-Oleum Mathys 108 Surfa Etch Solution is an easy to use, non-flammable and virtually odour free etching solution for the preparation of smooth concrete surfaces, masonry, galvanized steel and aluminum before applying a paint coating system.Improves the adhesion of coating systems Neutralizes alkaline salts Also ideal to remove "white...
£67.06 (incl. VAT)
£55.88 (ex. VAT)
General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site.Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects Click to jump down to...
£12.04 (incl. VAT)
£10.03 (ex. VAT)
Floor Application Kit from Rawlins Paints provides all the application equipment needed to apply conventional floor paints and coatings to a professional standard. The application of floor coatings is often crucial to their performance, so it is important to use the right tools to ensure a lasting finish.Each kit contains:12" Roller,...
£101.58 (incl. VAT)
£84.65 (ex. VAT)
