Resuprime ST (formerly known as Resuprime) is a two-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces. Features and Benefits: Versatile for many types of application Excellent adhesive properties Easy to apply Can be used as a tack coat for screeds No...
RSL FasTop Multi TG69
FasTop Multi TG69 (formerly known as Resuthane TG69) is a water-based polyurethance floor screed that handles everything a workplace can throw at it. Its thermal shock, chemical attack and abrasion protection makes it ideal for any heavy duty industrial environment.
- Chemical resistant
- Anti-slip finish
- Hot water & steam resistant
- Self sealing
- Matt finish
- Food safe and non-taint
FasTop Multi TG69 (formerly known as Resuthane TG69) has fast become the number one choice for the food and drinks sector. Approved by the Campden BRI & Chorleywood Food Research Association, it is cleaner-friendly, in that it can sustain boiling water and steam cleaning up to 100 degrees when applied with a 9mm thickness.
RSL were contracted to create a durable floor for the world-famous Billingsgate Fish Market in Canary Wharf, London. Opting for their Forest Green shade, Resuthane TG69 now covers the ground floor and is ideal for wet and dry surfaces with its excellent anti-slip components. It was also chosen for KP Nuts' new packaging facility in Rotherham.
- Food manufacture & processing
- Brewing & beverage
- Commercial Kitchens
- Pharmaceutical & chemical plant processing
- Abattoirs and meat processing facilities
- Heavy duty plant and traffic area
New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm sq. is required.
Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water.
Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. if the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.
To ensure the maximum bond is achieved, grooves must be cut into the perimeter of the subfloor, typically 20mm deep by 10mm wide. These should be inset approximately 150mm from, and running parallel with the walls and adjacent to any doorways, plinths etc. including any finished edge, i.e. both sides of a day work joint. The groove must have a neat square edge and the FasTop Multi TG69 laid to the full depth forming a perimeter anchorage.
Open and porous substrates will require priming with Resuprime ST on dry substrates only with less than 75% ERH reading. Where the Relative Humidity of a substrate exceeds 75% ERH Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.
The number of coats to be applied is chosen in accordance with the following table:
ERH% Required Coating Thickness
75-85 1 coat of Resuprime MVT at 200 microns per coat
85-92 2 coats of Resuprime MVT at 200 microns per coat
92-97 3 coats of Resuprime MVT at 200 microns per coat
For further information please refer to individual product data sheets.
FasTop Multi TG69 may be applied to substrates with a surface temperature in the range of 5-20°C and a relative humidity <90% RH, with a minimum air temperature of 8°C and no condensation. Do not pre-warm this product as working times will be substantially reduced if materials are warm.
When the primed surface is tack free FasTop Multi TG69 should be applied at the required rate as soon after mixing as possible. (Delay can result in variation in surface finish, colour and add to application problems).
NB: Cure times are extended at low temperatures.
Mixing: Mix the coloured base component to an even consistency, ensuring the re-dispersion of any settled pigment. Thoroughly scrape the contents of the base and hardener components into the same container and mix thoroughly for one minute. Pour the combined base and hardener into a rotary drum mixer and add the aggregate component steadily, until a homogeneous mix of the three components is achieved.
Apply to pre-primed areas and level between battens as necessary with a steel float, alternatively a sledge can be used set at the required thickness and again finished with a steel float. Where ease of cleaning is very important alongside slip resistance, the final finish can be smoothed by back rolling with a short nap roller. A single pass with the weight of the roller is usually sufficient.
FasTop Multi units should be applied consistently with mixes from the same batch, used consecutively where adjacent areas are being laid.
PU Cover with Taper
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Steel Float/Sledge
- 30 kg will cover 2.35 sq m @ 6mm or 1.57 sq m @ 9mm
- Touch Dry
Be the first to ask a question about this product!
RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood. Features and Benefits:...