Resuseal WB is a multi-purpose, two-pack, water-based epoxy coating primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish. Low odour Silica Free Superb adhesion Hard wearing Hygienic Dust-free Some product colours are made to order and have minimum...
Resutile ST and Clear is a hard-wearing, two-pack polyurethane floor coating which is designed to provide exemplary protection from any abrasion, chemicals or impact. It also removes graffiti.
- Chemical resistant and UV stable
- Abrasion, thermal shock and impact resistant
- Hygienic & easy to clean
- Impressive flexibility - high temperature resistance
- Skydrol resistant
- Available coloured (ST) or clear - please note that colours may have longer leader times due to being made to order
- Choose from 180+ RAL colours
Resutile ST & Clear is a high performance, two pack polyurethane floor coating which is designed to provide excellent chemical resistance and light fastness. It is a hard wearing and tough but flexible coating with very good resistance to impact, abrasion and high temperature. Resutile is regularly used in the aviation industry due to its excellent resistance to Skydrol.
Resin Surfaces Limited have over 20 years of experience in the Aerospace industry, and Resutile is the coating applied to these high-traffic areas.
It is resistant to engineering lubricants such as Hyjet and Skydrol. Resutile can be found at some of the UK's largest airports in baggage halls, cargo terminals and aircraft hangars, including London Heathrow, Manchester, Leeds Bradford, Gatwick and Luton.
With its anti-slip properties, it is also excellent for fire stations, production lines and any other vehicular areas.
- Aircraft hangars
- Prisons and police cells
- Chemical plants
- Pharmaceutical areas
- Medical and Healthcare
- Anti-slip finishes
- Graffiti removal
Resutile is available clear (Resutile Clear) or in a range of colours (Resutile ST) below, as well as over 180 RAL colours:
|Colour||Nearest RAL Match||Size||Finish|
|Flint Grey||RAL 7005||5L||Gloss|
|Salsa Red||RAL 3011||5L||Gloss|
|Stirling Grey||RAL 7004||5L||Gloss|
Please note that standard colours (above) and RAL/BS colours may have extended lead times, as these are made to order.
New Concrete Floors: New concrete must be clean, sound, dry and fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm² is required.
Timber Floors: Must be clean, sound and dry. Old clear varnish/topcoat must be removed/sanded prior to application, as it may affect the inter- coat adhesion with Resutile.
Existing Concrete Floors: Remove all dirt, oil, grease, old paints or any or other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing. Local repairs should be carried out using Resuscreed PA or Resuscreed 45.
Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.
Where Resutile is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface. Where surfaces are found to be porous a primer coat may be required to achieve a uniform sealed surface.
Resutile may be applied direct to concrete or as a seal coat or top coat to a resin floor system specified in our datasheets where a primer is not required. When applied direct to porous substrates the surface may require priming. Dry surfaces may be primed with Resuseal WB Clear or Resuprime ST.
Where the relative humidity of the substrate exceeds 75%, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.
The number of coats to be applied is chosen in accordance with the following table.
ERH% Required Coating Thickness
75-85 1coat of Resuprime MVT at 200 microns per coat
85-92 2coats of Resuprime MVT at 200 microns per coat
92-97 3coats of Resuprime MVT at 200 microns per coat
The ambient temperatures of the area should not be allowed to fall below 10°c throughout application and curing. Surface temperature must be above 5°c.
Mixing: Pre-mix the base component to a uniform consistency then add the entire contents of the hardener to the base and mix by using a slow speed hand held powered mixer and mixing paddle for approximately two to three minutes to achieve consistent mixture.
Note: Do not use a separate mixing bucket as it may affect the mixing ratio.
Apply the whole mixed paint by using spreading rake, roller and brush to achieve the maximum coverage within the specified pot life time frame.
Do not add solvent to this product.
Slip resistance can be improved by lightly broadcasting anti slip aggregates on the first coat (after primer) whilst still wet and back rolling, at a rate of 50/100 g/m2 . When cured apply the second Resutile coat to secure the aggregates. Alternatively, one pack of R.S. Beadgrip can be added to each pack of Resutile to achieve a fine non-slip texture.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Rake, Roller, Brush
- 5 litres will cover 50m sq. @ 100 microns wet thickness.
- Touch Dry
- 6 Hours
Be the first to ask a question about this product!
Resuprime ST (formerly known as Resuprime) is a two-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces. Features and Benefits: Versatile for many types of application Excellent adhesive properties Easy to apply Can be used as a tack coat for screeds No...
Resuscreed 45 is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish. ADVANTAGES Less dust than other screeds Low odour Hard wearing Abrasion and impact resistant Can form coving and falls Can be feather edged Can act as a...
RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood. Features and Benefits:...
RSL Resuscreed PA (formerly known as Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments. Features and Benefits: Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum surface preparation