Coo-Var Profloor Plus FH
Coo-Var Profloor Plus FH is a fast curing version of Coo-Var Profloor Plus. This two-pack, solvent free epoxy resin coating is designed to allow the laying and recoating of a surface within the same working day. It is particularly valuable where rapid return to service is required, or where the economics of a contract require that two coats may be required in the same working period.
- Fast-Curing high build coatings are obtainable in one application.
- Easily cleaned surfaces, unaffected by strong detergents.
- Good colour stability.
- Can be disinfected and sterilized.
- Slip resistant and abrasion resistant finishes can be achieved.
- Solvent Free.
Coo-Var Profloor Plus FH is a fast curing version of the Coo-Var Profloor Plus product. This two-pack, solvent free epoxy resin coating is designed to allow the laying and recoating of a surface within the same working day. Coo-Var Profloor Plus FH is particularly valuable where rapid return to service is required, or where the economics of a contract require that two coats may be required in the same working period. Coo-Var Profloor Plus FH achieves its best performance in the range 15-25°C.
Coo-Var Profloor Plus FH floor coating is suitable for use in most industrial environments, on concrete, polymer screeds, asphalt etc. and provides a durable, decorative, attractive and easily cleanable surface. The faster speed of cure makes this product particularly useful in the recoating of areas with minimal delay or down time.
Being low odour, Coo-Var Profloor Plus FH is ideal for use in the food industry for preparation, processing, storage areas, bakeries, dairies and breweries etc. where solvent based products are unsuitable. The hard wearing and chemical/oil resistant properties also make Coo-Var Profloor Plus FH ideal to use in showrooms, display areas, supermarkets, warehouses and workshops.
Coo-Var Profloor Plus FH - A fast hardening grade with good chemical resistance, should not be applied in temperatures below 15°C
New Floors: New concrete must be clean, sound, dry and fully cured and surface laitance removed, preferably by shot blasting, mechanical abrasion or chemical etching.
Existing Floors: Remove all dirt, oil, grease or other surface contaminants, preferably by shot blasting, scarification or mechanical planing. Fats, oils or greases must be removed by mechanical abrasion and detergent washing.
The working temperatures of the areas should not be allowed to fall below 12 °C throughout the application and curing period, otherwise the cure of the material will be retarded and surface finish adversely affected. Ensure that the floor area is clear and prepared, and that all equipment etc is readily available prior to mixing.
Mix the entire contents of the base with the hardener thoroughly, using a slow speed electric mixer. Take care to mix the product thoroughly but do not over mix as this will reduce working time with the product.
Lay the product off evenly with a notched trowel, squeegee etc and then back-roll. Note the speed of reaction will result in cure in the roller after a period of time care should be taken to replace rollers regularly and to handle the used roller with care as this may be hot. Residual /or unused materials will generate heat and should be placed in a well ventilated area to allow to cure. Do NOT add any materials to the product or container during application of the material or when curing off residual materials .
Clean tools and equipment with xylene or Coo-Var Thinners 16 immediately after use.
Coo-Var Profloor Plus FH systems offer excellent chemical resistance against dilute mineral acids, alkalis, detergent solutions and certain solvents. Coo-Var Profloor Plus FH achieves the maximum chemical resistance on full cure. Avoid chemical contact or aggressive cleaning within three days of application. Remove chemical spillages as quickly as possible to prevent concentration by evaporation. Contact the Technical Department for advice on resistance to specific chemicals.
Please Note: This product has a minimum order quantity of 20 x 5kg per colour and is subject to a 7 - 10 working day lead time. Special colours can be produced, but may be subject to a surcharge and extended lead times - Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Base Type
- Check Safety Sheet For Details
- Pot Life (at 20°C)
- 15 minutes
- 4-5m² per KG
- Recommended Thinner/Cleaner
- Thinner 16
- Solids by Volume
- Touch Dry
- 3-4 Hours
- UN Number
Be the first to ask a question about this product!