Tikkurila Temafloor 210 Clear is a solvent-free varnish used for dust binding, priming and topcoating especially where solventless and odourless products are needed. The lacquer can be used for patching when filled with sand.
Good resistance against abrasion, oils and grease.
Also for dust binding and priming of new and old concrete floors prior to laying Temafloor epoxy coatings and screeds; especially where solventless and odourless products are needed.
Can be used as a finishing varnish in the Mosaic flooring system.
Filled with sand also suitable for patching of concrete floors.
Used as a binder for Temafloor 4000 Compact troweling screed.
Tikkurila Temafloor 210 Clear is a solvent-free varnish used for dust binding, priming and topcoating especially where solventless and odourless products are needed. The lacquer can be used for patching when filled with sand.
Temafloor 210 Clear is widely used and has the highest quality. It has good resistance against abrasion, oils and grease. Varnish forms glossy, smooth and non-yellowing finish. Temafloor 210 Clear can be applied with mosaic flakes as a top lacquer.
Good resistance against abrasion, oils and grease.
Also for dust binding and priming of new and old concrete floors prior to laying Temafloor epoxy coatings and screeds; especially where solventless and odourless products are needed.
Can be used as a finishing varnish in the Mosaic flooring system.
Filled with sand also suitable for patching of concrete floors.
Used as a binder for Temafloor 4000 Compact troweling screed.
Suitable also for topcoating of concrete floors indoors.
Technical Data
Volume Solids: Approx. 100%
Specific Gravity: 1.1 kg / litre (mixture)
Pot Life (23℃): Approx. 30 minutes after mixing, on substrate
Practical Coverage:
Coverage on concrete floors is on average:
Primer: 5 – 8 m²/l
Topcoat: 6 – 10 m²/l
Practical coverage depends on the porosity and evenness of the substrate and on the application method.
Mixing Ratio:
Base: 2 parts by volume Temafloor 210 Clear
Hardener: 1 part by volume 008 4431
Drying Time (23℃)
Dust dry after 6 hours
Recoatable after 16 - 24 hours
Light trucking after 24 hours
Fully cured after 7 days
Surface Preparation
New Concrete
Remove laitance by power grinding or hydrochloric acid etching.
Choose the method best suited for the premises.
After grinding remove dust carefully with a vacuum cleaner.
Hydrochloric acid etching is carried out with diluted hydrochloric acid (1 part concentrated hydrochloric acid, 4 parts water).
Rinse with plenty of water.
Dry the surface.
Old Concrete
Remove all grease, oil, chemicals and other impurities by Maalipesu detergent.
Remove old peeling paint layer by grinding.
Choose the method best suited for the premises.
Clean out pot-holes removing all loose friable material.
Open cracks with e.g. an abrasive tool.
Remove loose material and dust.
If cementitious screed is used, check compatibility with the levelling screed manufacturer.
Application Conditions
The relative humidity of the concrete should not exceed 97%.
The temperature of the ambient air, surface or coating should not fall below +15ºC during application or drying.
Relative humidity of air should not exceed 80%.
Note! There is a natural tendency of this coating to chalk, discolor or yellow unevenly. It is recommended to use polyurethane topcoat when there are high aesthetical requirements on colour appearance.
Mixing Components
First stir base and hardener separately.
Mix the correct proportions of base and hardener thoroughly (approx. 2 minutes to get homogenous mixture) by using a low speed industrial hand drill with a paddle.
Use power mixer for mixing.
Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the coating and risk the success of the application.
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets.
For industrial and professional use only.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Tikkurila Temafloor 210 Clear is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Tikkurila Temafloor 200 Primer is a two-component solvent-free epoxy varnish. It gives good adhesion for Temafloor coatings and screeds and dries fast. Short overcoating time enables whole system application in one day.Thinned Temafloor 200 Primer penetrates well into the pores of the concrete sealing the surface and giving good adhesion...