• RSL Resuline
  • RSL Resuline
  • RSL Resuline

RSL Resucoat LM

RSL Resucoat LM (formerly known as Resuline) is a high-build, fast-curing epoxy coating floor system for applying lines to surfaces. It has a high coloured gloss finish and minimum creep even on textured surfaces.

Features and Benefits: 

  • One coat
  • Fast setting
  • Glass beads and clear aggregates can be applied
  • Easy to use
  • Colour stability
  • 200 to 500 microns thickness
Colour
  • Current colour: White
Choose a colour
Close colour picker
  • White
  • Black
  • Poppy Red
  • Savannah Yellow
  • Forest Green
Size
Finish
£39.54
VAT excluded

£47.45 Tax incl.
Quantity

Description

RSL Resucoat LM (formerly known as Resuline) is ideal for demarcation lines, pedestrian direction, truck routing and road signage. It can be applied to a variety of surfaces with the right preparation, such as concrete, cement and even sand screeds.

Its fast-curing pedigree makes it great for industrial environments which don't wish to close for works, such as walkways, hospital corridors or food courts. Where footfall is high and inevitable, Resucoat LM will give your floor some clear instruction. 

Recommended Uses

  • Pedestrian road signage
  • Hospital floors
  • Car and plane lines
  • Walkways and demarcation
  • Pharmaceutical labs

Preparation

New Concrete Floors: New concrete must be clean, sound, dry, and fully cured and surface laitance removed, preferably by vacuum enclosed shot blasting or mechanical grinding. A minimum strength of 25N/mm squared is required.

Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing. Make sure all residue of detergent is washed and removed by rinsing with clean water.

Local repairs should be carried out using Resuscreed PA or Resuscreed 45.

Coated Surfaces: Prepare surface to ensure that there is an adequate mechanical key. Care should be taken to ensure compatibility between the existing surface and Resucoat LM.

Set out line markings as required, marking positions with tape or chalk as appropriate. Ensure that all surfaces are prepared before mixing and only mix materials as required.

Priming

Open and porous substrates may require priming with Resuseal WB, also Resuprime ST may be used as a primer on dry substrates, only with less than 75% ERH reading. Where the relative humidity of a substrate exceeds 75% ERH, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table:

ERH% Required Coating Thickness
75-85 - 1 coat of Resuprime MVT at 200 microns per coat
85-92 - 2 coats of Resuprime MVT at 200 microns per coat
92-97 - 3 coats of Resuprime MVT at 200 microns per coat

For Further information please refer to recommended individual product data sheets, or call our technical team.

Application

The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally, to allow the ambient and substrate temperature to stabilise prior to installation.

Mixing: Pre-mix the coloured base component to a uniform consistency, then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used, mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two minutes or until the two components have fully combined.

Application methods should be selected based on the size and area to be covered, and the thickness of the line to be applied. Short or medium pile good quality rollers or brushes should be used, or straight edges such as trowels can be used if applying to tapes. Spread the material rapidly and then roll to finish. Remove tapes shortly after application, by pulling across the line. Do not hold bulk materials in a pot or scuttle, as this increases the rate of reaction reducing the working time. Ensure that rollers are changed regularly to prevent cure of materials in the roller.

Resucoat LM is not normally recoated. If required, re-coat as soon as the surface is tack free (i.e. 4 hours later). For the best inter-coat adhesion, Resuline should be applied no later than 24 hrs after previous coatings.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details

Data sheet

Application
Brush, Roller, Trowel.
Coverage
2.5 kg. will cover 62 linear metres @ 240 microns thickness 100mm wide.
Touch Dry
4-5 Hours
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

RSL Resuseal WB

Resuseal WB is a multi-purpose, two-pack, water-based epoxy coating primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish.  Low odour  Silica Free  Superb adhesion  Hard wearing  Hygienic Dust-free Some product colours are made to order and have minimum...

Price £50.53
In stock

RSL Resuprime ST

Resuprime ST (formerly known as Resuprime) is a two-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces.  Features and Benefits: Versatile for many types of application Excellent adhesive properties Easy to apply Can be used as a tack coat for screeds No...

Price £68.19
In stock

RSL Resuprime MVT

RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood.  Features and Benefits:...

Price £19.80
In stock