• RSL Resuline
    • RSL Resuline
    • RSL Resuline

    RSL Resuflor LM


    RSL Resuflor LM (formerly known as Resucoat LM and Resuline) is a high-build, fast-curing epoxy coating floor system for applying lines to surfaces. It has a high coloured gloss finish and minimum creep even on textured surfaces.

    • One coat
    • Fast setting
    • Glass beads and clear aggregates can be applied
    • Easy to use
    • Colour stability
    • 200 to 500 microns thickness
    • Forest Green available only with 100 minimum order quantity and 7 working day lead time

    Pick a Colour
    • Current colour: White
    Close colour picker
    • White
    • Black
    • Poppy Red
    • Savannah Yellow
    • Forest Green
    £59.89(ex. VAT)
    £71.86 (inc. VAT)
    Please choose your colour
    Available for Delivery (See Delivery Options Below)


    RSL Resuflor LM (formerly known as Resucoat LM and Resuline) is ideal for demarcation lines, pedestrian direction, truck routing and road signage. It can be applied to a variety of surfaces with the right preparation, such as concrete, cement and even sand screeds.

    Its fast-curing pedigree makes it great for industrial environments which don't wish to close for works, such as walkways, hospital corridors or food courts. Where footfall is high and inevitable, Resuflor LM will give your floor some clear instruction. 

    Recommended Uses

    • Pedestrian road signage
    • Hospital floors
    • Car and plane lines
    • Walkways and demarcation
    • Pharmaceutical labs


    New Concrete Floors: New concrete must be clean, sound, dry, and fully cured and surface laitance removed, preferably by vacuum enclosed shot blasting or mechanical grinding. A minimum strength of 25N/mm squared is required.

    Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing. Make sure all residue of detergent is washed and removed by rinsing with clean water.

    Local repairs should be carried out using Resuflor Patch or Resuflor Screed.

    Coated Surfaces: Prepare surface to ensure that there is an adequate mechanical key. Care should be taken to ensure compatibility between the existing surface and Resuflor LM.

    Set out line markings as required, marking positions with tape or chalk as appropriate. Ensure that all surfaces are prepared before mixing and only mix materials as required.


    Open and porous substrates may require priming with Resuflor WB, also Resuprime ST may be used as a primer on dry substrates, only with less than 75% ERH reading. Where the relative humidity of a substrate exceeds 75% ERH, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.

    The number of coats to be applied is chosen in accordance with the following table:

    ERH% Required Coating Thickness
    75-85 - 1 coat of Resuprime MVT at 200 microns per coat
    85-92 - 2 coats of Resuprime MVT at 200 microns per coat
    92-97 - 3 coats of Resuprime MVT at 200 microns per coat

    For Further information please refer to recommended individual product data sheets, or call our technical team.


    The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally, to allow the ambient and substrate temperature to stabilise prior to installation.

    Mixing: Pre-mix the coloured base component to a uniform consistency, then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used, mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two minutes or until the two components have fully combined.

    Application methods should be selected based on the size and area to be covered, and the thickness of the line to be applied. Short or medium pile good quality rollers or brushes should be used, or straight edges such as trowels can be used if applying to tapes. Spread the material rapidly and then roll to finish. Remove tapes shortly after application, by pulling across the line. Do not hold bulk materials in a pot or scuttle, as this increases the rate of reaction reducing the working time. Ensure that rollers are changed regularly to prevent cure of materials in the roller.

    Resuflor LM is not normally recoated. If required, re-coat as soon as the surface is tack free (i.e. 4 hours later). For the best inter-coat adhesion, Resuline should be applied no later than 24 hrs after previous coatings.

    Product Details

    Data sheet

    For Use By
    Industrial Use
    For Use On
    Concrete Floors
    Application Method
    Single, Two or Three Pack
    2.5 kg. will cover 62 linear metres @ 240 microns thickness 100mm wide.
    Touch Dry
    4-5 Hours
    Base Type
    Base Type
    Suitable For Use On
    Concrete Floors
    Suitable For Use On
    Coated Surfaces
    Application Method
    Application Method
    Application Method
    Product Type
    Product Range
    Colour Family
    Colour Family
    Colour Family
    Colour Family
    Colour Family

    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

    Be the first to ask a question about this product!

    Question about the product

    * Required fields


    RSL Resuflor LM is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT

    You might also like

    RSL Resuflor WB - Standard Readily Available Colours

    Resuflor WB (formerly known as Resuseal WB) is a multi-purpose, two-pack, water-based epoxy coating primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish.  These standard colours are readily available with faster shipping options; more colours are also available...

    Price £179.39 (ex. VAT)
    In Stock and Available for Delivery

    RSL Resuprime ST Bonding & Priming Coat

    Resuprime ST (formerly known as Resuprime) is a two-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces.  Features and Benefits:Versatile for many types of application Excellent adhesive properties Easy to apply Can be used as a tack coat for screeds No...

    Price £108.46 (ex. VAT)
    In Stock and Available for Delivery

    RSL Resuprime MVT

    RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood. Easy application Use on...

    Price £147.10 (ex. VAT)
    In Stock and Available for Delivery