Rust-Oleum 5200 Epoxyshield Ultra

    5268.5
    RUS442

    Rust-Oleum 5200 Epoxyshield Ultra is a 5 litre, satin finish, quick-drying single pack water-based floor coating for garage floors, and light to medium duty (normal foot traffic/limited vehicular traffic): 

    • Part of the Epoxyshield range
    • Good resistance to diesel, motor oil, coolant fluid, various household chemicals and most types of tyre
    • For concrete and garage floors
    • Easy to apply and touch dry after just 2 hours
    Colour
    £57.64(ex. VAT)
    £69.17 (inc. VAT)
    Quantity
    Please choose your colour
    In Stock and Available for Delivery (See Delivery Options Below)

    Description

    Rust-Oleum 5200 Epoxyshield Ultra

    A quick-drying single pack water-based floor coating (epoxy-modified acrylic) for light to medium duty (normal foot traffic/limited vehicular traffic).

    • Single pack, water based
    • For light to medium traffic
    • Easy to apply
    • Touch dry after just 2 hours
    • Satin matt finish
    • Good resistance to car tyres and various chemicals

    Good resistance to diesel, motor oil, coolant fluid, various household chemicals and most types of tyre. EpoxyShield®5200 ULTRA can be applied on concrete floors which are completely clean, dry and treated with EpoxyShield® Sealer 5220. Do not apply to smooth and completely sealed concrete or concrete containing a curing compound. Such substrates will prevent a good adhesion. Can also be applied on old good adhering coatings.

    Technical Data

    • Density: 1,16 - 1,21
    • Gloss Level: Satin
    • Solids content in volume: 38% - 42%
    • Solids Content in weight: 48-52%

    Drying Times At 20°C/RH 50%

    • Touch dry: 2 hours (20°C), 4 hours (10°C), 1½ hours (30°C)
    • Dry to handle: 6 hours (20°C), 8 hours (10°C), 4 hours (30°C)
    • Dry to recoat: 6 hours (20°C), 8 hours (10°C), 4 hours (30°C)
    • Fully cured: 1 week (20°C), 1 week (10°C), 1 week (30°C)

    Theoretical Consumption

    Approx. 9 m²/l at 40 µm dry

    Practical Consumption

    Approx. 9 +/- 2 m²/l. Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.

    In order to improve abrasion resistance the product can be mixed with Rust-Oleum Ultra Wear 400. One packaging (750 gram) is sufficient for 5-litre product. The mixture must be stirred regularly in order to prevent settling on the bottom of the can. In case of petrol spilling/leakage do not wipe the floor dry but let evaporate. The coating will restore itself. It is advisable to wait for at least 1 week after application before parking a vehicle.

    Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.

    Product Details
    442-946863

    Data sheet

    For Use By
    Consumer Use
    Interior / Exterior Use
    Interior Use
    For Use On
    Concrete Floors
    Application Method
    Brush
    Roller
    Sheen
    Satin
    VOC Levels
    Low (50-149 g/l)
    Single, Two or Three Pack
    Single
    Pack Size
    5L
    Dry to Handle (at 20°C)
    6 Hours
    Dry to Recoat (at 20°C)
    6 Hours
    Fully Cured (at 20°C)
    1 Week
    Coverage
    9m² per litre
    Max. Application Temperature
    35°C
    Min. Application Temperature
    10°C
    Solids by Volume
    38% - 42%
    VOC
    72g/L
    Shelf Life (from date of manufacture)
    5 years
    Touch Dry
    2 Hours
    Recommended Dry Film Thickness
    40 µm
    Recommended Wet Film Thickness
    100 µm
    Base Type
    Epoxy-Modified Acrylic
    Base Type
    Water-Based
    Suitable For Use On
    Garage Floors
    Suitable For Use On
    Concrete Floors
    Finish
    Matt
    Application Method
    Roller
    Application Method
    Brush
    Usages
    Abrasion Resistant
    Usages
    Chemical Resistance
    Usages
    Oil Resistant
    Product Type
    Topcoat
    Fastest Delivery
    Next Working Day
    Colour Family
    Grey
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    questions James on 2023-08-13 09:42:56
    Question: 

    How many litres would I need for two coats on a single garage floor?

    Answer from Rawlins’ Technical Team: 

    This would depend on how large the area is you need to cover. 

    The coverage rate of this product is 9m² per litre per coat.

    In the case of roller application it can be necessary to apply 2 coats.

    questions Karla  on 2022-07-31 22:19:21
    Question: 

    Would this be ok ok a terracotta tiled floor??

    Answer from Rawlins’ Technical Team: 

    Assuming the terracotta tiled floor is porous, only subjected to foot traffic, it is clean, dry, sound and prepared as detailed in the technical data sheet this could be used.

    questions robert young on 2022-03-08 14:54:56
    Question: 

    I am looking to paint my garage floor with Rust-Oleum 5200 Epoxyshield Ultra. As in most garages, the majority of the concrete floor is internal. However about 30cm of it protudes externally under the garage door, so it is permanently external. Can i use the 5200, with 5220 sealer, on this portion as well as on the internal garage floor? Is there anything suitable to apply on top of the 5200 if needed, or is the 5200 still OK in external as well as internal? Many thanks

    Answer from Rawlins’ Technical Team: 

    Yes these products can be applied to concrete internally or externally.

    There is not a topcoat we can recommend to over paint this with.

    questions John Knight on 2021-12-15 15:55:16
    Question: 

    Going to put this on my garage floor, approximately 30 years old. do I need to put a sealer on first or is it ok to apply this only.

    Answer from Rawlins’ Technical Team: 

    Assuming the garage floor is clean, dry, sound and prepared as detailed in the technical data sheet, in most circumstances grinding the floor or acid etching the concrete will be required prior to application, then Rust-Oleum 5220 Epoxyshield Sealer should be applied prior to application of the floor paint.

    questions Jason on 2021-02-28 15:49:12
    Question: 

    Can I use the RUST-OLEUM EPOXYSHIELD DECORATIVE FLAKES with this paint?.Also,can you apply this paint with a brush? Thank you.

    Answer from Rawlins’ Technical Team: 

    Rust-Oleum Epoxyshield Decorative Flakes are designed for use with 2 pack epoxy coatings such as the Rust-Oleum Garage Floor Kit or Rust-Oleum 5300 Epoxyshield Maxx. It is likely that the paint film will be too thin if using 5200 Epoxyshield Ultra to get a good hold of the flakes and ensure they stay in place. Rust-Oleum 5200 Epoxyshield Ultra can be applied with brush or roller.

    questions oliver on 2019-09-18 17:25:53
    Question: 

    can this be used on setcrete high performance self levelling compound. This SLC is designed as a wear surface. What primer would I use in conjunction with the SLC and Epoxy Ultra? Many Thanks

    Answer from Rawlins’ Technical Team: 

    If the self levelling product you have used can be left as a wearing surface and the manufacturer of the product is happy for it to be coated with single pack water-based floor coatings (epoxy-modified acrylic) then yes Rust-Oleum 5200 Epoxyshield Ultra could be used.

    The data sheet for Rust-Oleum 5200 Epoxyshield Ultra states the followin under preparation;

    Remove oil, grease and all other contaminants with Rust-Oleum Epoxyshield Cleaner / Degreaser in combination with high pressure cleaning. Allow new concrete to set for at least 30 days before applying a coating. Remove laitance, loose and damaged concrete by sandblasting or etching with Rust-Oleum Mathys 108 Surfa Etch Solution. Repair all holes and cracks with EpoxyShield concrete repair products. Always pre-treat absorbent, porous surfaces with Rust-Oleum 5220 Epoxyshield Sealer. Roughen or blast well-sealed and smooth concrete and treat withRust-Oleum 5220 Epoxyshield Sealer or apply a coat Rust-Oleum 3333 Super Adhesion Primer. Roughen still-intact floor coatings to ensure good adherence. Remove poorly adhering old coatings with wire brush and sandpaper. During application the surface must be clean and dry.

    questions Laura on 2019-02-28 18:08:14
    Question: 

    I used one cost of the rustoleum 5200 Epoxy sealer last year on my concrete floor. Is it Ok to now use this epoxy paint to paint over it. Even though the sealer was put on about 8 months ago. I have cleaned the floor thoroughly. Will it still work well or do I need to grind it back to the original concrete & start from scratch?

    Answer from Rawlins’ Technical Team: 

    Rust-Oleum 5220 Epoxyshield Sealer is recommended to prime/seal floors before Rust-Oleum 5200 Epoxyshield Ultra so you will not need to remove it. Before applying Rust-Oleum 5200 Epoxyshield Ultra, ensure the floor is clean, dry and lightly sand the Rust-Oleum 5220 Epoxyshield Sealer if necessary to remove any gloss and provide a key.

    questions Olly on 2018-11-12 22:38:08
    Question: 

    I have a concrete floor slab, flat but only hand smoothed. Is the sealer/primer a necessity?

    Answer from Rawlins’ Technical Team: 

    Yes, the data sheet states 'Always pre-treat absorbent, porous surfaces with Rust-Oleum 5220 Epoxyshield Sealer.'

    questions Harriet wright on 2018-11-07 09:15:58
    Question: 

    Would thus paint be suitable for use on floorboards in a bedroom and do you need to use a primer with it as old floorboards are currently bare wood.

    Answer from Rawlins’ Technical Team: 

    Rust-Oleum 5200 Epoxyshield Ultra is recommended for concrete surfaces, for domestic floorboards customers have previously used Blackfriar Professional Acrylic Floor Paint. Bare surfaces require a sealer (Blackfriar Professional Water Based Floor Sealer or for small areas dilute Blackfriar Professional Acrylic Floor Paint with 10% water), then apply 2 coats of the floor paint as recommended. The coating should be allowed to fully harden before moving furniture about. Allow 7 days for the coating to cure hard. Any sharp objects moved across the floor may damage the coating, felt pads can be used under chair legs, bed frame lags etc and will minimise any damage.

    questions Jonty on 2018-05-01 09:50:26
    Question: 

    Can I use this rust-eleum 5200 to put over a pre existing vinyl floor?

    Answer from Rawlins’ Technical Team: 

    No.

    questions Barbara Smart on 2017-09-06 13:41:36
    Question: Is the water based rust oleum 5200 epoxyshiled ultra a low odour paint? Thanks
    Answer from Rawlins’ Technical Team: 

    Being water based, when used in the intended industrial/commercial environments Rust-Oleum 5200 Epoxyshield Ultra is indeed a low odour paint. Please note however this does not mean a NO odour paint.

    questions Vladimira Kezele on 2017-03-17 21:31:43
    Question: Can Epoxyshield 5200 Ultra be used for covering o an old concrete path around the house (outside)?If not, what would you recommend for outside old concrete?
    Answer from Rawlins’ Technical Team: 

    Rust-Oleum Tarmacoat has a larger colour range and would be more suited to this type of external application.

    questions Lisa Buckland  on 2015-08-04 08:50:36
    Question: 

    Can Rust-Oleum 5200 Epoxyshield Ultra be used on wooden floorboards in a kitchen?

    Answer from Rawlins’ Technical Team: 

    No, but you could use Timberex Aqua Plus

      

    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    Rust-Oleum 5200 Epoxyshield Ultra is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    COVERAGE CALCULATOR
    Units
    Film Thickness
    Total area²
    Or enter length and width dimensions:
    Length
    Width

    *All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage

    You might also like

    Rust-Oleum Epoxyshield Cleaner / Degreaser

    Rust-Oleum 2901 Epoxyshield Cleaner/Degreaser for floors is a concentrated, alkaline, non-flammable, virtually odour-free cleaning/degreasing solution.Removes grease, oil and other contaminations Virtually odour free Non-flammable 6-8 m²/l coverageMore Information Delivery Info

    Price £45.33 (ex. VAT)
    In Stock and Available for Delivery

    Rust-Oleum Epoxyshield Decorative Flakes

    Rust-Oleum Epoxyshield Decorative Flakes (Chips) are intended for use with their Epoxyshield Garage Floor Coating or Epoxyshield Maxx however it can also be used with other Rust-Oleum Mathys Floor Coating Systems.One sachet will cover approximately 25m² Broadcast/Scatter the flakes by hand or sieve Can be used in conjunction with...

    Price £7.42 (ex. VAT)
    In Stock and Available for Delivery

    Rust-Oleum 5200 Epoxyshield Ultra

    Rust-Oleum 5200 Epoxyshield Ultra is a 5 litre, satin finish, quick-drying single pack water-based floor coating for garage floors, and light to medium duty (normal foot traffic/limited vehicular traffic): Part of the Epoxyshield range Good resistance to diesel, motor oil, coolant fluid, various household chemicals and most types of tyre...

    Price £57.64 (ex. VAT)
    In Stock and Available for Delivery

    Rust-Oleum 5300 Epoxyshield Maxx

    Rust-Oleum 5300 Epoxyshield Maxx is a 5 litre, gloss finish, water-based 2-component epoxy concrete floor coating with ultimate adhesion and durability on concrete.Part of the Epoxyshield range Maximum durability in just 1 coat For medium to heavy traffic Best possible car tyre resistance Easy to apply, no primer required Note:...

    Price £81.49 (ex. VAT)
    In Stock and Available for Delivery

    Rust-Oleum Epoxyshield Fine Crack Repair

    Rust-Oleum Epoxyshield Fine Crack Repair Mortar is a specially developed, non-shrink, solvent-free, two part epoxy:Liquid crack filler for concrete floors for fine cracks up to 3mm wide Creates a smooth even finish. Dry in 3-4 hours (at 20°C) To recoat after 4 hours (at 20°C) 500 ml for 25 meters (2mm wide, 5mm deep) FREE plastic...

    Price £28.95 (ex. VAT)
    In Stock and Available for Delivery

    Rust-Oleum Epoxyshield Garage Floor Coating Kit

    Rust-Oleum Epoxyshield Garage Floor Coating Kit is a two-component epoxy formula for the ultimate garage floor, saving time and providing an easy clean, showroom-quality appearance on concrete floors. Complete DIY kit including decorative chips/flakes, paint paddle, instructions and DVD One kit covers up to 25m² Durable and timesaving...

    Price £74.34 (ex. VAT)
    In Stock and Available for Delivery

    Rust-Oleum Epoxyshield Concrete Repair Mortar

    Rust-Oleum Epoxyshield Concrete Repair Mortar is for levelling and repairing cracks, holes and other damages in concrete, cement renderings and unpainted brickwork: Just add water, stir and its ready for use Light traffic possible after 24 hours (at 20°C) To recoat after 48 hours Sandable to a smooth finish For horizontal and vertical...

    Price £63.10 (ex. VAT)
    In Stock and Available for Delivery

    Rust-Oleum 5220 Epoxyshield Sealer

    Rust-Oleum 5220 Epoxyshield Sealer is a one-component, water-based, concrete sealer based on a vinyl acrylic binder: Part of the Epoxyshield range Reduces dust production on concrete Protects against moisture, road salts, liquid and chemical spills Suitable for garage floors Cost-effective, quick drying and easy to apply Touch dry...

    Price £42.23 (ex. VAT)
    In Stock and Available for Delivery

    Floor Application Kit

    Floor Application Kit from Rawlins Paints provides all the application equipment needed to apply conventional floor paints and coatings to a professional standard. The application of floor coatings is often crucial to their performance, so it is important to use the right tools to ensure a lasting finish.Each kit contains:12" Roller,...

    Price £84.65 (ex. VAT)
    In Stock and Available for Delivery