Rust-Oleum Mathys Pegakote is an easy to apply, two-pack, water based, epoxy coating for interior floor and wall surfaces in garages, warehouses, showrooms, corridors, indoor car parks, workshops, etc.
Available in 4,400+ colours, inc. RAL, RAL Design, BS, NCS & the new NCS 2050 colours
New Sizes - Now Available in 5L and 10L Pack Sizes
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cart
Rust-Oleum Mathys Pegakote is a two-pack, water based, epoxy coating for interior floor and wall surfaces in garages, warehouses, showrooms, corridors, indoor car parks, workshops, etc.
Pegakote dries to a very hard finish which provides exceptional abrasion resistance (Taber Abrasion weight loss after 1000 cycles: ± 110 mg (CS17, load: 1000g)) and is resistant to oils and solvents. It is solvent free, almost odourless and easy to clean leaving a smooth, stain finish.
Airless spray: Nozzle: 015 - 017 / Pressure: 220 bars. 1st coat: dilute with 5-10% water. 2nd coat: dilute with max. 5% water
Application Conditions
Minimum 8°C and maximum 80% R.H.
Consumption
Theoretical: 6m²/L/coat
Practical: Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application
Cleaning of Equipment/Spills
Water
Remarks
In order to become a solid gloss finish, please respect the consumption quantities of the second layer, this means that a tin of 5 L has to be applied on a surface of 6-8 m² which is 30-40m² for 5 litres
Always provide good air ventilation; so even when it rains, windows and doors have to be opened wherever possible.
The 2 components must be mixed under mechanical agitation.
For use on floors submitted to heavy abrasion, standard and medium colours are recommended. In case of deep and/or bright tones (red, yellow, orange, green, blue etc), it is mandatory to apply a PU varnish e.g Rust-Oleum 4900 Polycoat 2K
Roller application of epoxy coatings may cause markings, especially in dark/deep colours. These represents a purely optical appearance and has no influence on the quality of the coating. If the focus is on the decorative aspect, it will be necessary to apply a transparent topcoat or alternatively use airless application
If used in garages, car parking areas, garage workshops, etc. it is mandatory to prepare the substrate mechanical (blasting or diamond sanding. Chemical etching is no alternative). As a first coat always apply Rust-Oleum 5401 Epoxy Impregnation Primer*according to substrate condition
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
I have just purchased Rust-oleum Pegakote floor paint, at the moment I have a new concrete base I intend to use the paint on, should I seal the base first or will the paint go straight on?
Answer from Rawlins’ Technical Team:
The substrate should be dry and clean, free from ascending humidity and sufficiently coherent (tensile strength min. 6kg/cm²). Rust-Oleum Mathys Pegakote can be applied directly on most mineral substrates (for instance old concrete, tiles, glass etc.). Curing compounds in case of poly-concrete have to be removed by means of sand or grit blasting. On new concrete or non-porous concrete, remove cement grout by sand or grit blasting, treatment with diluted hydrochloric acid at a ratio of 3 litres hydrochloric acid to 10 litres water or with Rust-Oleum Mathys 108 Surfa Etch Solution. For these two last solutions, there is obligation to rinse abundantly and to allow drying through of the surfaces. Porous substrates shall be impregnated with Rust-Oleum Mathys Pegakote diluted with 10-20% water. Rust-Oleum Mathys Pegakote may not be applied on an elastic paint coat or a moving substrate.
Richard Branch on 2019-04-24 11:33:53
Question:
I want to paint my garage floor. It's 20 year old concrete in good condition. I am interested in the self leveling qualities of this product but am confused by the consumption. The floor area is 50 Sq Mtrs. and the product info says use 4kg / Sq Mtr for up to 3mm leveling but that would suggest I require 200 Kg per coat so 400 kg for 2 x coats! Surely that can't be correct?
Answer from Rawlins’ Technical Team:
Rust-Oleum Mathys Pegakote is no longer recommended by Rust-Oleum for self-levelling applications, instead we would recommend 306 Self Levelling Floor Coating. To apply a 3mm layer to 50m² you would require 11 x 25kg units.
chris on 2016-11-16 10:43:20
Question: Can this floor paint be applied over concrete floorings previously covered with an epoxy paint or a polymer resin paint.
Answer from Rawlins’ Technical Team:
Assuming that the underlying floor substrate is solid with no damages and is not moving in any way, and that the previously (correctly applied and cured) epoxy layer remains in good condition and well adhered to the underlying substrate, then yes Rust-Oleum Mathys Pegakote can be applied on top.
In all instances, the existing surface should be thoroughly degreased using a 5% solution of Rust-Oleum Mathys ND14 Cleaner Degreaser and then sufficiently abraded by the most suitable method (e.g. blasting, grinding, etc.)
Ross & Co on 2016-09-27 14:15:57
Question: We have recently painted Floors in a University with Rustoleum Pegakote and the client is now asking what type of product they should use to clean the floors . Regards, David Ross
Question: Can this product be applied directly onto Cementone Cempolay self levelling screed?
Answer from Rawlins’ Technical Team:
If you have used the standard Cempolay then this is not strong enough to take an epoxy coating, it is designed to be over laid with vinyl, wood floor, tiles, etc. If you have used Cempolay Ultra Strong, then this is strong enough to take an epoxy floor coating and the Pegakote should be fine to be applied after preparation.
Jennifer Holburn on 2015-12-13 21:13:31
Question:
Which of the epoxy paints is most suitable for painting a wet room floor?
Answer from Rawlins’ Technical Team:
Rust-Oleum 5500 Solvent Free Epoxy would be a good choice assuming the area you have to paint is bare concrete. You might also want to consider adding an anti-slip aggregate into the system for some slip resistance.
Rust-Oleum Mathys Pegakote is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Rust-Oleum Mathys 108 Surfa Etch Solution is an easy to use, non-flammable and virtually odour free etching solution for the preparation of smooth concrete surfaces, masonry, galvanized steel and aluminum before applying a paint coating system.Improves the adhesion of coating systems Neutralizes alkaline salts Also ideal to remove "white...
Floor Application Kit from Rawlins Paints provides all the application equipment needed to apply conventional floor paints and coatings to a professional standard. The application of floor coatings is often crucial to their performance, so it is important to use the right tools to ensure a lasting finish.Each kit contains:12" Roller,...