Ennis-Flint MMAXGRIP PRMX Catalyst is an essential component of MMA–based Ennis-Flint products. When mixed with Ennis-Flint MMA products it both starts and adjusts the curing reaction. The reaction speed can be influenced by adjusting the amount added, and this method is used to adapt the reaction to the ambient conditions (temperatures). Easily soluble,...
Rust-Oleum Non-Skid Additive NS 300
Rust-Oleum Non-Skid Additive NS 300 is based on thermally split flint stones and is intended to be added to floor coatings to produce a non-skid surface. Can be mixed with the required Rust-Oleum coating system or can be sprinkled into the freshly applied coating manually or with special low pressure spraying equipment.
Rust-Oleum Non-Skid Additive NS 300 is based on thermally split flint stones and is intended to be added to floor coatings to produce a non-skid surface. Rust-Oleum Non-Skid Additive NS 300 can be used in combination with the following Rust-Oleum Floor coatings:
Rust-Oleum Non-Skid Additives can be mixed with the required Rust-Oleum coating system or can be sprinkled into the freshly applied coating manually or with special low pressure spraying equipment. Rust-Oleum Non-Skid Additives are intended for Non-Skid industrial flooring and should be topcoated with the required Rust-Oleum System if sprinkled.
Directions for Use
Sprinkling: Sprinkle the granulates onto the freshly applied, wet Rust-Oleum coating, manually with a "sprinkler-box" for small areas, or with special low-pressure spraying equipment with a nozzle opening of at least 18mm; air pressure between 1 - 3 bars.
Mixing: Mix the granulates into the wet coating material and apply the coating with a roller or a brush (not by spraying), stir regularly to avoid settling of the granulates.
Note: For coating systems with a dry film thickness less than 300μm it is recommended to use NS 200.
- Sparingly: 20 m²/kg (= 200 g/l if mixed in)
- Dense: 10 m²/kg (= 400 g/l if mixed in)
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Be the first to ask a question about this product!
Remmers Ceramix 03 is a special, wear resistant, coloured blinding material to be used as blinding material for anti-slip covers and for the production of mortars and screed mixtures. Image already added
A hard silica quartz aggregate is an additive that conforms with parts KU1 C/D and KF1 E/F of BS5493, providing additional under foot traction to floor coatings. Advantages Helps to prevent accidents on wet floor areas Stir directly into paint Cream in colour ISO 9001:2008 & ISO 14001:2004
Rust-Oleum Non-Skid Additive NS 500 is a specially selected non-skid additive that can be mixed with the required Rust-Oleum coating system or sprinkled into the freshly applied coating to produce a non-skid surface.
A specially formulated quartz aggregate to be added to various products in our floor coatings range to provide increased 'anti-slip' properties in both dry and wet conditions to improve safety. Broadcast/sprinkle into the freshly applied wet coating and over coat once dry to encapsulate the additive fully.
Sikafloor Pronto Pigment is a coloured powder used to colour certain Sikafloor Pronto products. Sikafloor Pronto Pigment is pre-mixed with a disovler and then added in measured quantities to the selected products resin base. See the Sikafloor Pronto product data sheet for specific details on how to use.
Sikafloor Pronto Filler is fine white aggreagate filler of specific grading that should be used as an additive with certain Sikafloor Pronto products to create self-smoothing screeds and levelling mortars.
A specially formulated quartz aggregate to be added to various high build products in our floor coatings range to provide increased 'anti-slip' properties in both dry and wet conditions to improve safety.
Sikalastic Fleece 120 is a non-woven, needle-punched polyester fleece reinforcement to enhance the strength and durability of various Sika systems. Sikalastic Fleece 120 is ideal for crack bridging, waterproofing and strengthening applications displaying complex details and geometry or when accessibility is limited.
Remmers WHG TX is a thixotroping agent for solvent-free, Remmers epoxy resin floor coatings. It is used to produce compounds in a filling consistence for rising building elements such as face sides, hollow coves, plinth upstands and stair steps. Image already added
Sikafloor Earthing Kit is a system of anchored brass plates with a stable earth connection. Each box contains 10 connections and at least 2 per room should be used - see coating system data sheet for more details.
Remmers Floormix DQ Aggregate is a special blend of graded decorative colour quartz aggregate for the production of epoxy mortar screeds. Can be laid at 3 - 4mm and available in a wide range of colour blends. Blend with any of the Remmers epoxy resins as a binder.
Sikalastic 827 LT is a modified hot-melt adhesive with defined volume increase and chemical bond activated by the hot asphalt used as part of the bridge deck waterproofing system underneath mastic asphalt and asphalt concrete.
Remmers Ceramix 07 is a mixture of coloured quartz with a special aggregate grading curve for coloured blinded floor covers used as blinding material for slip-resistant coverings and for the production of mortars and screed mixes. Coloured quartz sand with grain size of approx. 0,2 - 0,7 mm, e.g. for use as aggregate for Remmers decorative pebble...
Remmers Add 250 is a wear resistant, transparent, chemical resistant polymer granulate. By adding the polymer spheres to liquid sealing materials, transparent as well as coloured, slip resistant sealants can be produced. Image already added