Watco Block Paving Stabiliser

PAVSEELSF25
WAT9310

Watco Block Paving Stabiliser has proved to be the ultimate answer to the problems associated with fixing the essential jointing sand and helping to protect the integrity of block paving in some of the world’s most demanding applications.

  • Inhibits water/fuel penetration and weed growth
  • Withstands vacuum cleaning and resists jointing sand removal
  • Strengthens pavements and reduces maintenance costs

Colour
Size
£223.99(ex. VAT)
£268.78 (inc. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

Description

Quick Links - Click To Jump To Section:




Features & Benefits


  • Areas of use:
    • Footpaths
    • Pedestrian precincts
    • Domestic driveways
    • Office car parks
    • Retail parks and highways
  • Reduces maintenance costs
  • Resists jointing sand removal
  • Withstands vacuum cleaning
  • Strengthens pavements
  • Inhibits water/fuel penetration and weed growth
  • Long performance life
  • Easy to apply
  • Stable under normal UV radiation



Surface Preparation


Surfaces to be treated must be dry, free from grease, oil, dirt and previous coatings. Joints should be filled or topped up to the bottom of the chamfer with clean, dry compacted sand of the correct specification.



Application


Ground temperatures should be between 10°C and 30°C

Apply only when the blocks, jointing sand and bedding sand are dry and when rain is not expected for at least 24 hours. Only one application is required. Pour directly from the container or apply with a watering can fitted with a rose. Low pressure spray systems can also be used. Do not flush out the jointing sand. Work in areas of approximately 5m2 , distributing the liquid evenly with a foam rubber squeegee. Ensure that the joints are completely filled with liquid and that the joints and pavers have absorbed as much solution as they can. Use the squeegee to remove all unabsorbed liquid from the surface of the pavers.

Please Note – the product must not be allowed to pond on the surface of the pavers or create a surface film. Any unabsorbed material must be pushed away using the squeegee. Dry conditions at the time of application are important since damp or rain in contact with uncured Watco Block Paving Stabiliser can cause the product to dry with a whitish ‘bloom’. This effect will be exaggerated if any surplus solution is not removed from the blocks with the squeegee at the time of application.



Limitations


  • Only suitable for application to bare, unsealed standard concrete block pavers, with a joint width not exceeding 3mm - 5mm
  • Not suitable for joints between paving slabs, flagstones, etc. where the joint width could be considerably more
  • Watco Block Paving Stabiliser must not be flushed down drains, storm drains or allowed to enter open water courses



Product Details
PAVSEELSF25

Data sheet

Manufacturer
Watco
For Use By
General Use
For Use On
Concrete block pavers
Application Method
Watering can fitted with a rose or low pressure spray system, Foam rubber squeegee
Single, Two or Three Pack
Single Pack
Pack Size
25L
Coverage
Between 2m2 and 2.5m2 per litre, depending on the porosity of the pavers, block size and joint width. The joint width on standard concrete block paving is usually determined by a nib on the edges of each block, and this should not be exceeded.
Max. Application Temperature
30°C
Min. Application Temperature
10°C
Shelf Life (from date of manufacture)
24 months in unopened container.
Fully Cured
Surfaces treated can normally be re-opened to foot traffic within 12 - 24 hours. Protect from rain and frost while curing. A warm dry wind will speed curing time.
Colour(s)
Clear
Base Type
Water-Based
Exterior / Interior Use
Exterior & Interior Use
Suitable For Use On
Concrete
Application Method
Squeegee
Application Method
Spray
Application Method
Watering Can
Components
1K
Product Type
Acrylic
Product Type
Sealer
Colour Family
Clear
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send