• Resupen WB
  • Resupen WB

RSL Resupen WB

Resupen WB is a an extremely durable polyurethane finish for concrete, plaster and wood that produces a resilient coating on Sherwin-Williams wall and flooring systems. It is available in clear, colour, matt and satin finish.

ADVANTAGES

  • Chemical resistant
  • UV stable
  • Good abrasion and impact resistance
  • Hygienic and easy to clean
  • No VOC’s
  • Resistant to hot water
  • Minimum order quantities for colours apply, which may increase lead times
    • See Ordering References below
Colour
  • Current colour: White
Choose a colour
Close colour picker
  • Clear
  • White
  • Black
  • Poppy Red
  • Salsa Red
  • Stirling Grey
  • Flint Grey
  • Savannah Yellow
  • Kingfisher Blue
  • Tuscan Green
  • Forest Green
  • Marigold
Size
Finish
£105.44
VAT excluded

£126.53 Tax incl.
Quantity

Description

Ordering References


Colour Nearest RAL Match Size Finish Mimimum Order Quantity
Clear - 5 Litre Matt or Satin 1
Black RAL 9017 5 Litre Matt or Satin 15
Buff RAL 1002 5 Litre Matt or Satin 15
Flint Grey RAL 7005 5 Litre Matt or Satin 15
Marigold RAL 1005 5 Litre Matt or Satin 15
Salsa Red RAL 3011 5 Litre Matt or Satin 15
Savannah RAL 1032 5 Litre Matt or Satin 15
Stirling Grey RAL 7004 5 Litre Matt or Satin 15
White RAL 9003 5 Litre Matt or Satin 15
Forest Green RAL 6002 5 Litre Matt or Satin 15
Kingfisher Blue RAL 5017 5 Litre Matt or Satin 15
Poppy Red RAL 3020 5 Litre Matt or Satin 15
Tuscan Green RAL 6011 5 Litre Matt or Satin 15

Colours with minimum order quntities may experience longer lead times as these are made to order.

Resupen WB is a durable top coat which can be applied to a range of Resin Surfaces Limited (RSL) products. It is resilient and can produce an attractive matt or satin finish to floors or walls. Wall coatings are available in pastel shades, whilst floors can be finishing in Flint or Stirling.

Resupen WB was applied to RSL's Resutop at Thanet Earth in Kent to produce an excellent matt finish. With its seamless appearance, high resistance and self-smoothing qualities, it was the ideal finish for the country's largest crop production site.

RECOMMENDED USES

  • As a seal coat for other Sherwin-Williams floor coatings and screeds
  • Laboratories
  • Food factory units
  • Prisons and police cells
  • Pharmaceutical areas 
  • Medical and healthcare
  • Can be used on floors and walls

Preparation

New Concrete Floors: New concrete must be clean, dry and fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm2 is required.

Timber Floors: Must be clean, sound and dry. Old clear varnish/topcoat must be removed/sanded prior to application, as it may affect the inter- coat adhesion with Resupen WB.

Existing Concrete Floors: Remove all dirt, oil, grease, old paints or any or other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing. Local repairs should be carried out using Resuscreed PA or Resuscreed 45.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advise on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.

Where Resupen WB is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface. Where surfaces are found to be porous a primer coat may be required to achieve a uniform sealed surface.

Priming

Resupen WB may be applied direct to concrete or as a seal coat or top coat to a resin floor system specified in our datasheets where a primer is not required. When applied direct to porous substrates the surface may require priming. Dry surfaces may be primed with Resuseal WB Clear or Resuprime NT.

Where the relative humidity of the substrate exceeds 75%, Resuprime MVT should be specified and selected on Resuprime MVT the basis of hygrometer readings in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table:

ERH% Required Coating Thickness
75-85 1coat of Resuprime MVT at 200 microns per coat
85-92 2coats of Resuprime MVT at 200 microns per coat
92-97 3coats of Resuprime MVT at 200 microns per coat

Application

The ambient temperatures of the area should not be allowed to fall below 10°c throughout application and curing. Surface temperature must be above 5°c.

Mixing: Pre-mix the base component to a uniform consistency then add the entire contents of the hardener to the base and mix by using a slow speed hand held powered mixer and mixing paddle for approximately two to three minutes to achieve consistent mixture. Note: Do not use a separate mixing bucket as it may affect the mixing ratio.

Apply the whole mixed paint by using spreading rake, roller and brush to achieve the maximum coverage within the specified pot life time frame.

Do not add water to this product.

Slip resistance can be improved by lightly broadcasting anti slip aggregates on the first coat (after primer) whilst still wet and back rolling, at a rate of 50/100 g/m.sq.  When cured apply the second Resupen WB Clear coat to secure the aggregates. Alternatively, one pack of R.S. Beadgrip can be added to each pack of Resupen WB Clear to achieve a fine non-slip texture.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details

Data sheet

Application
Rake, Roller, Brush
Coverage
5 litres will cover 50m. sq. @ 100 microns wet film thickness.
Touch Dry
6-8 Hours
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Robert Brindley on 18/12/2018
Question: 

Can you supply samples of the available colours to apply on concrete floors?

Answer: 

We have a colour card we can send out or if you have specific colours you would like we can advise which is the closest or for larger orders bespoke colours can be produced to meet your colour scheme.


Question about the product

* Required fields
(read)
Send
You might also like

RSL Resupen WB

Resupen WB is a an extremely durable polyurethane finish for concrete, plaster and wood that produces a resilient coating on Sherwin-Williams wall and flooring systems. It is available in clear, colour, matt and satin finish. ADVANTAGES Chemical resistant UV stable Good abrasion and impact resistance Hygienic and easy to clean No VOC’s...

Price £105.44
In stock

RSL Resuscreed 45

Resuscreed 45 is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish. ADVANTAGES Less dust than other screeds Low odour Hard wearing Abrasion and impact resistant Can form coving and falls Can be feather edged Can act as a...

Price £59.30
In stock

RSL Resuscreed PA

RSL Resuscreed PA (formerly known as Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments. Features and Benefits:  Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum surface preparation

Price £38.44
In stock
16 other products in the same category:

Coo-Var Oil Tolerant Primer

Coo-Var Oil Tolerant Primer is a two-component epoxy resin membrane that is tolerant of residual oil contamination in concrete floors. Designed to improve the adhesion of coatings and screed systems to surfaces that have previously been contaminated with oils, that may still retain some residual contamination. Product Features Enables...

Price £107.56
In stock

Remmers PUR Aqua Top 2K M Plus

Remmers PUR Aqua Top 2K M Plus is a water based, textured, silk matt, transparent, 2-component sealant with good resistance to UV-light and chemicals. Class R 11 slip resistance which can be used as a slip resistant, silk matt sealant. Slip-resistant sealant for surfaces subjected to light mechanical loads Silk matt Slip-resistant...

Price £94.95
In stock

Remmers Epoxy BS 2000 Transparent New

Remmers Epoxy BS 2000 Transparent is a water emulsifiable, epoxy resin for versatile use, used as an impregnation agent or adhesion promoter in surface protection systems. It can also used as a bonding layer worked wet-on-wet in combination with levelling compounds or epoxy resin systems. Ideal for warehouses, garages, parking garages,...

Price £55.72
In stock

Hydron Mona-Guard Extra

Conforming to EN 1504-2, the Mona-Guard Extra Natural Stone Sealer is an excellent sealer for environments which are subject to high traffic or public spaces, where resistance to oil, water, weathering and UV are important. Other Key Benefits Reduce costs: only one coat is required. Many applications: use on dense, low porous substrates....

Price £69.25
In stock

Sikafloor Comfort Adhesive

Sikafloor Comfort Adhesive is a 2-part, total solid, low VOC PUR adhesive that is part of the Sika ComfortFloor Pro and Sika ComfortFloor Decorative Pro System used to adhere Sikafloor Comfort Regupol 6015H and Sikafloor Comfort Regupol 4580 to concrete and cementitious screeds. Features and Benefits: Good bonding properties Low VOC Non...

Price £163.94
In stock

Sikafloor 220 W Conductive

Sikafloor 220 W Conductive is a two part, water dispersed, epoxy resin primer with high electrostatic conductivity. Must be applied as a primer underneath all Sikafloor conductive wearing courses on concrete and cementitious screeds for different types of industrial use. Features and Benefits: Highly electrostatically conductive Easy...

Price £117.16
In stock

Rust-Oleum 5130 Primer DSP

Rust-Oleum 5130 Primer DSP is a super-high solids two pack epoxy resin primer designed for the suppression of vapour pressure effects. Creates a barrier to stop rising moisture and vapour pressure Prevents blistering For use on asphalt and concrete Very low solvent content High build system

Price £42.84
In stock

RSL Resuprime PU

Resuprime PU, a two component, solvent free polyurethane primer designed for use on car parking decks and other areas where a more flexible solution is required, with excellent adhesion to a wide variety of substrates. Its degree of flexibility compliments the properties of the Resudeck ID and Resudeck TD systems. Good flexibility High...

Price £112.00
In stock

SCHÖNOX SDG

SCHÖNOX SDG is a very low emission special dispersion primer ready for use, suitable for the fast pre-treatment of unheated cementitious screeds with increased residual moisture up to 4.0 CM-% (85%-rh).

Price £158.13
In stock

Sikafloor 161

Sikafloor 161 is an economic two-part epoxy primer, levelling mortar and intermediate layer epoxy resin primer for Sikafloor systems and a binder for Sika levelling mortars and screeds. Features and Benefits Moisture tolerant Low viscosity Good penetration Excellent bond strength Easy application Short waiting times Solvent-free...

Price £119.26
In stock

Ennis-Flint CP Primer

Ennis-Flint CP Primer is a high quality, thin solvent based resin solution for priming concrete surfaces, used to improve adhesion between concrete and surface materials, e.g. hot melt bituminous compounds, thermoplastic or epoxy resin.

Price £50.02
In stock

Remmers PUR Aqua Top 2K SG

Remmers PUR Aqua Top 2K SG is a water based, transparent sealant with a silk gloss for indoor areas suitable for all Remmers Epoxy and PUR coatings. It can also be used for fixating and sealing Remmers flake coatings. Water based, silk gloss, transparent, 2-component sealant with good resistance to UV-light and chemicals. Image already added...

Price £307.28
In stock

RSL Epo-Flex VJ

RSL Epo-Flex VJ (formerly known as Resujoint V) is a flexible, thixotropic, two-component epoxy joint sealant designed to accommodate low level movement in vertical and horizontal joints. Features and Benefits:  Tough, yet flexible Adhesive Easy to clean Good chemical resistance Accommodates movement Maintains a seamless finish

Price £43.93
In stock

Hydron Nu-Base Hydroseal

Nu-Base Hydroseal is the ideal concrete floor sealer to suppress the effect of residual moisture in concrete. For example, if laying down tile flooring on top of concrete, it is first necessary to "seal-in" concrete from moisture, including residual moisture inside the concrete. Ideal for Pubs and clubs Industrial warehouses Dwellings Public...

Price £96.25
In stock

Bradite Floor Primer

Bradite Floor Primer is a clear coating solution to prime power floated, non-porous concrete and quarry tiles ready for top coating. Excellent for food areas due to it's low-odour and non-taint solution. Manufactured under the auspices of an ISO 9001:2008 & ISO 14001:2004. Advantages Primer and topcoat can be applied the same day...

Price £128.99
In stock

Remmers Epoxy UV 100

Remmers Epoxy UV 100 is a UV-protected, transparent, epoxy resin with a wide application spectrum. It is used for decorative pebble or Color Quartz covers, for fixating flake coatings and as a glossy, thick layer sealant on decorative substrates. Ideal for workshops, fabrication halls, exhibition or assembly rooms, retail and wholesale...

Price £63.63
In stock